Global demand for electricity is growing significantly in developing nations. Renewable energy accounts for barely 3% of total energy consumption in Bangladesh. Sources of renewable energy, e.g. solar, are increasingly being acknowledged as viable supply-side choices for microgrids. This article presents a grid-connected microgrid design based on meteorological data for a local community situated in Mohammadpur, Dhaka. This study presents a feasible design of a system that gives the lowest cost of energy production and emissions that is evaluated using software named Hybrid Optimization Multiple Energy Resources (HOMER Pro). Comparison and assessment of the net present cost, cost of energy, operating cost and environmental emission for five different feasible microgrids are analysed concerning real-time data. Also, a suitable case is sorted out and proposed for the local community for electrification. The proposed case offers a $0.0442/kWh cost of energy, which is ~32% cheaper than the current rate with a 57.5% renewable fraction and a payback period of 16.86 years. People of this local community will have access to considerably more clean energy at a lower price by this study; also this design could sell the excess energy to the grid to avoid frequent electricity outages.
The pollution and toxic greenhouse gases produced by fossil fuel combustion are troubling as global energy demand continues to rise. To mitigate the consequences of global warming, a transition to sustainable energy sources is necessary. This manuscript presents a feasible community microgrid design in Hazaribagh, Dhaka based on meteorological data that leads to photovoltaic installation on the rooftop of a local community building. This study shows a microgrid design of a system with the lowest cost of energy and a large renewable fraction, which is analysed using the HOMER Pro software. Using real-time data, analysis of the system cost, cost of energy, renewable fraction, unmet load, energy purchased and energy sold is discussed. A suitable case for electrification is also identified and presented for the selected community. The proposed case yields a cost of energy of $0.0357/kWh, which is 52% less than the current tariff rate, with a 70% renewable fraction. This study will provide people in this community with more green energy at a lower cost; in addition, this designed microgrid sells additional energy to the grid to avoid possible power outages. The potential for a positive energy community is also investigated in terms of energy consumption and renewable output of the planned microgrid.
Renewable energy systems (RES) are becoming more prominent because of the depletion of natural resources. Optimum sizing of the hybrid RES is necessary to ensure that renewable energy sources penetrate. Improper sizing may result in higher initiating costs or an inability to meet load demand under various weather conditions. By analyzing with Hybrid Optimization Multiple Energy Resources (HOMER pro), this study shows the ideal hybrid energy system that provides the lowest cost of energy production, emissions, and so on. This study provides a grid-connected hybrid power system model based on metrological data collected from a residential building in Mohammadpur, Dhaka, Bangladesh. Solar energy is used as a sustainable energy source thus the cost of the system was decreased, which is also environmentally friendly. This renewable energy also helped to minimize the levelized cost of energy (COE). The conclusion estimates operational costs, production costs, net present cost, and energy cost for the two combinations evaluated for the proposed microgrid system. According to the simulation results, delivering power to the load via a microgrid would be a viable and cost-effective solution.
This manuscript aims to propose a fourth industrial revolution-based approach to electricity distribution and management systems. The energy meter measures electrical energy, and it is inspected by a person where consumption bills are prepared depending on the meter reading. Most often, the bills are prepared based on the meter reading i.e., manually by hand which tends to be unreliable, expensive, time-consuming, and error prone. Energy meter monitoring using image processing and a computerized billing system is a feasible process that can eliminate conventional meter reading, saves time and money, increase accuracy, prevent electricity theft, and prevent peak hour costs. This manuscript focuses on remote monitoring and controlling of individual loads, energy meter monitoring, forecast analysis depending on industrial electricity consumption, and a digital billing system. Load forecast will help the user further to take managerial decisions. Furthermore, this prototype exhorts the user to turn off the highest energy-consuming load during peak hours and help to reduce peak hour demand as well as the energy cost of the user. Concisely, this system is designed to provide a better, safer, and simpler distribution system to the users and electricity suppliers.