1 March 2021 in IEEE Transactions on Microwave Theory and Techniques
This article demonstrates an inaudible attack on smart speakers using electromagnetic interference (EMI). The EMI induces voltages on the order of a few millivolts on conductors, which are then converted into baseband signals by exploiting the inherent nonlinearity of microphones. The EMI signal is specially preprocessed to minimize the useless harmonics generation at the microphone output signals, which significantly improves the recognition rate as well as nullify the previous countermeasures based on the harmonics detection. The sensitive carrier frequency found by our proposed method can improve the attack distance as well. A measurement-based methodology is applied to locate the sensitive regions for noise coupling without knowing the layout of the printed circuit board (PCB), and the transfer function is also obtained to insure the main coupling location. Our experiments show that in open space, intentional EMI under 2.5 W can inject commands at distances up to 2.5 m on smart speakers.
21 June 2021 in IEEE Transactions on Microwave Theory and Techniques
This article proposes a jitter-aware decoupling capacitors placement optimization method that uses the genetic algorithm (GA). A novel method for defining the optimization target function in regard to power delivery network (PDN) and power source-induced jitter (PSIJ) optimization based on the GA-based tool is proposed. The proposed method can provide an optimum and economic solution for the number of decoupling capacitors to use in a PDN to reach the target impedance. Then, by modifying the optimization target function with our proposed method, an optimum solution of the number of decoupling capacitors regarding the PSIJ can be obtained. The PSIJ analytical expressions are derived in conjunction with a resonant cavity model that includes the coordinates of the decoupling capacitors and the PSIJ transfer function. The GA-based optimization algorithm with the proposed target function is first applied to optimize the number of decoupling capacitors regarding the PSIJ. Finally, the measured jitters from HSPICE simulation results are used to verify our optimization method such that both the simulated results and analytically calculated results support the efficiency of our proposed optimization method.
19 February 2021 in IEEE Transactions on Microwave Theory and Techniques
This article proposes an optimization algorithm using the Hessian minimization method, based on the Newton iteration, to evaluate the effectiveness of the placement of multiple decoupling capacitors on a power/ground plane pair. The exact effective decoupling regions are obtained using the Newton iteration method for each decoupling capacitor. The impedance of the IC port is lower than the target impedance no matter where the decoupling capacitor is placed in this region. To optimize specific capacitor placements in this region, the Newton iteration, based on the Hessian matrix, is used to determine the location where the impedance of the IC port is minimized at the antiresonant frequency of the plane pair. This placement optimization algorithm allows for a decoupling design method that can also be applied to a PDN with multiple decoupling capacitors for multiple IC ports. Compared with the method of random selection from within the effective decoupling area, the method proposed here requires fewer decoupling capacitors and less computational time.
22 October 2020 in IEEE Access
This paper aims to develop an original circuit theory of inductorless NGD topology. The considered passive cell comprised of resistor and capacitor elements without inductor operates as a bandpass (BP) NGD function. The specifications of NGD functions are defined. Generally, the BP NGD fully lumped circuits available in the literature operate with resonant RLC-network. In the introduced research work, a lumped circuit was first time identified to exhibit the BP behavior without the presence of inductive component. The inductorless BP NGD topology is inspired from the combination of low-pass (LP) and high-pass (HP) NGD passive cells. Therefore, an original LP-HP NGD composite topology is obtained. The identified BP NGD topology is constituted only by passive RC-networks. Then, theoretical development of BP NGD analysis is explored. The inductorless circuit theory starts with the identification of BP NGD canonical form. Then, the expressions of NGD value, center frequency and attenuation in function of RC-network parameters are established. The synthesis equations allowing to determine the resistor and capacitor elements are derived. Proofs-of-concept are designed and prototypes are fabricated to verify the effectiveness of the developed LP-HP NGD composite theory. To validate the developed original circuit theory, two prototypes of RC-network based LP-HP NGD composite were designed, fabricated, simulated and tested. The two prototypes were synthesized with respect to two different NGD center frequencies 13.5 MHz and 22 MHz. As expected, the calculated, simulated and measurement results are in very good agreement with NGD value of about some negative nanoseconds. In the future, the characterized inductorless topology enable to overcome the traditional limitations of RLC-network based BP NGD circuits because of inductance self-effect limitation.
30 July 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper develops a diakoptics modelling of a flying bird topology constituted by interconnected piece-wises of admittance or Y-matrices. The diakoptics principle is established with passive system teared into several simplex elements as transmission and coupled lines (TLs and CLs). After introduction of subsystem Y-matrix, the global system Y-and S-matrices are established. To verify the model effectiveness, parametric analyses enabling to understand bandpass negative group delay (NGD) behavior of the flying bird topology. Furthermore, a microstrip circuit is designed, fabricated and tested. The modeled, simulated and measured NGD circuit responses are in excellent agreement. NGD value about -2.2 ns under transmission and reflection coefficients better than -2 dB and -13 dB is measured around 1.15 GHz.
8 May 2019 in IEEE Transactions on Electromagnetic Compatibility
This paper investigates an original multiphysics KB modeling of the electrothermomechanical (ETM) phenomena in a multi-layer printed circuit board (PCB) under heat cycle aggression. The coupled thermal and intrinsic mechanical interactions with the PCB electrical response are analyzed. The via-interconnect line (IL) junction fatigue caused by the mechanical tensions is explained with tensorial equations. The ETM effects transduced between the PCB components are modeled with equivalent graphs. The multiphysics problem general tensorial relation is formulated. To validate the Kron-Branin model, the numerical application of three-layer PCB proof-of-concept under thermal cycle aggression with 0-to-70 °C variation is introduced. The tensile stresses induced by the thermal effect on the vias and ILs are calculated. The via cracking fatigue model is approximated. The PCB voltage transfer function and input impedance in the function of the thermal aggression are discussed.