Characterization studies of clays are often performed to identify possible markets for these materials. Bearing this in mind, two samples of natural clays from the Southeast region of Brazil were studied. Conventional techniques of characterization were used. Granulometric analysis and determination of cationic exchange capacity of these clays were also performed. Nitrogen adsorption-desorption measurements were used to determine the Brunauer-Emmett-Teller specific surface area, and Barrett-Joyner-Halenda and t-plot pore size analysis were carried out. The results obtained were similar for the two clays. Both present high clay fraction (above 80 wt%) composed of illite, kaolinite and quartz minerals. Stratified illite-smectite structures were also observed. Traces of calcite were detected in one of the clay samples, while traces of montmorillonite were observed in the other sample. These results were corroborated by the low cationic exchange capacity values obtained for both clays. These clays showed good adsorptive properties, evidenced by their specific surface areas, with predominantly mesoporous structures and slit-like pores. According to their features, these clays have potential use as adsorbents to replace more expensive materials due to their easy availability and low cost.
18 September 2019 in Journal of Thermoplastic Composite Materials
The aim of this study is to evaluate the effect of some experimental variables such as the content of styrene–ethylene–butylene–styrene (SEBS) and talc, processing conditions and mixing protocol on the properties of polypropylene (PP). To achieve this objective, PP/SEBS blends and PP/SEBS/talc composites were processed in a corotating twin-screw extruder. A masterbatch of PP/talc was prepared before the extrusion of PP/SEBS/talc composites. The morphology of blends and composites was evaluated by scanning electron microscopy, which revealed the dispersion of small rubber droplets in the PP matrix. Moreover, the micrographs also showed that SEBS and talc particles were uniformly dispersed and distributed in the polymer matrix. Results of thermal properties showed that talc had a nucleating effect, which promoted the increase of both PP crystallization temperature and crystallinity degree. The incorporation of talc in PP/SEBS blends led to an expressive increase in the impact resistance by 70% as compared with the reference blend: PP/SEBS 80/20% (w/w). This result reveals that although the PP/SEBS/talc composites showed a separated morphology, the good dispersion and distribution of this mineral filler in the polymers contributed to avoid crack propagation and increase the impact properties. The tensile properties in the elastic region were not significantly affected.
Blends of PHB and LDPE were prepared by melt mixing in a twin screw extruder. Castor oil cake (CC) was used as filler for the blends. The design of experiments (DOE) technique was used to evaluate the effect of the components proportion on the materials properties. The mechanical properties and morphology of the materials were evaluated. The LDPE Young's modulus increases but the other tensile properties and impact resistance deteriorate with the addition of PHB or CC. The tensile strength values of binary mixtures of LDPE lie in the range from 8.9 to 10 MPa. As some commercial grades of LDPE have mechanical strength in this range, it may be inferred that the addition of a certain amount of PHB or CC to LDPE may be considered as a possibility for obtaining LDPE based materials with increased susceptibility to biodegradation. The poor interfacial adhesion between the phases became visible in all samples.
LDPE blends based on PHB and GG biodegradable polymers were prepared by melt mixing in a twin screw extruder. The mechanical properties of the materials were evaluated. Preliminary information about the biodegradation behavior of the specimens was obtained by visual observation of samples removed from the simulated soil in 90 days. The results indicated that LDPE/PHB blends may be used for designing LDPE based materials with increased susceptibility to degradation, if elongation at break and impact properties are not determinant factors of their performance. LDPE based materials on GG present values of flexural and mechanical strength lower than those of LDPE/PHB blends. LDPE/PHB/GG blends exhibit unsatisfactory properties. Apparently, the effect of addition of GG to LDPE on the biodegradation behavior of LDPE/GG blends was less intense than the effect caused by addition of PHB to the blends. Similar observation has occurred with the partial replacement of GG by PHB in the ternary blends.
30 September 2010 in Polymer-Plastics Technology and Engineering
Composites of low density polyethylene were prepared by melt mixing in a co-rotating twin screw extruder. Castor presscake, a biodiesel process co-product, was used as filler for the polyethylene composites. Different concentrations of this filler were added to the polymer matrix. Melt flow index and. mechanical properties were measured by following standardized tests. The results showed that the addition of the filler to the polymer matrix provoked an increase on the values of Young Modulus and on the flexural properties. However, the impact strength and the tensile stress values tended to decrease with the increasing of the filler concentration.