10 December 2019 in IEEE Transactions on Instrumentation and Measurement
17 September 2018 in Sensor Review
Purpose: For the measurement of large-scale components in aircraft assembly, the evaluation of coordinate transformation parameters between the coordinate frames of individual measurement systems to the assembly frame is an essential task, which is usually completed by registration of the enhanced reference system (ERS) points. This paper aims to propose an analytical method to evaluate the uncertainties of transformation parameters considering both the measurement error and the deployment error of ERS points. Design/methodology/approach: For each measuring station, the measured coordinates of ERS points are first roughly registered to the assembly coordinate system using the singular value decomposition method. Then, a linear transformation model considering the measurement error and deployment error of ERS points is developed, and the analytical solution of transformation parameters’ uncertainties is derived. Moreover, the covariance matrix of each ERS points in the transformation evaluation is calculated based on a new uncertainty ellipsoid model and variance-covariance propagation law. Findings: For the transformation of both single and multiple measuring stations, the derived uncertainties of transformation parameters by the proposed analytical method are identical to that obtained by the state-of-the-art iterative method, but the solution process is simpler, and the computation expenses are much less. Originality/value: The proposed uncertainty evaluation method would be useful for in-site measurement and optimization of the configuration of ERS points in the design of fixture and large assembly field. It could also be applied to other registration applications with errors on both sides of registration points.
19 August 2019 in Measurement Science and Technology
Non-contact laser scanning is widely used in aircraft parts inspection and components assembly, especially for the dimensional error of complex structural parts. Careful scan path planning can greatly improve the measurement accuracy and efficiency of scanning. This paper presents a methodology to solve the design and optimization problems of scanning posture. The scanning quality is improved by reducing measurement uncertainty to obtain the optimum posture angle and spatial position for scanning. A posture coordinate system is established to obtain the posture angle deviation between the current scanning posture and the principal direction of all points in the corresponding measuring area, which quantifies the measurement uncertainty of the scanning area. The posture adjustment interval is defined according to the limit scanning envelope to search for the feasible direction and position of the scanner, and the measurement uncertainty of the scanning area is reduced by optimizing the posture angles iteratively. We demonstrate the effectiveness of the proposed method by comparing it with other posture planning algorithms.
12 March 2018 in Assembly Automation
Purpose: In aircraft assembly, standard reference points with nominal coordinates are commonly applied for coordinate transformation between multiple measurement stations and the assembly coordinate system. For several reasons in practical application, these points often fail to envelop the key assembly space, which leads to large transformation uncertainty. This paper aims to analyze and further reduce the coordinate transformation uncertainty by introducing a new hybrid reference system (HRS). Design/methodology/approach: Several temporary extension points without known coordinates are added to enhance the tightness between different stations, especially at the weakness area in the network, thus constituting an HRS together with the existing standard reference points. The coordinate transformation model of the HRS-based measurement network is established based on an extend Gauss–Markov model. By using the geometrical differential property and variance-covariance propagation law, the covariance matrixes in the transformation model are calculated, and the analytical solution of the uncertainties of transformation parameters are ultimately derived. The transformation uncertainty of each check points is presented by Helmert error expression. Findings: The proposed analytical solution of transformation uncertainty is verified using the state-of-the-art Monte Carlo simulation method, but the solution process is simpler and the computation expenses are much less. Practical implications: The HRS with three temporary extension points is practically applied to a tail boom in-site measurement for assembly. The average transformation uncertainty has been reduced by 26 per cent to less than 0.05 mm. Originality/value: The hybrid coordinate transformation model is proposed for the first time. The HRS method for transformation uncertainty reduction is more economical and practical than increasing the number of standard reference points.
22 May 2020 in Measurement Science and Technology
Measurement error compensation is a key issue for the application of laser trackers in an unsteady environment, especially in the nonuniform temperature field. Aimed at reducing induced measurement uncertainty, a measurement error compensation method with error similarity analysis is proposed in this paper. The spatial similarity of measurement errors is qualitatively analyzed based on the mathematical model, and quantitative analysis is presented by means of simulation and semivariogram. We then model the error similarity, and an error-estimation model for target points is established with the radius basis function neural network and regularized extreme learning machine. The experiments are conducted to verify error similarity and the applicability and accuracy of the estimation model in practice. The results show that error similarity does exist in practical measurements, and the proposed method can reduce the absolute measurement error to less than 0.03 mm ( ). The method is applicable for measurements in different environments since the compensated point sets are almost coincident.
4 October 2018 in Measurement Science and Technology
In the process of feature extraction, geometric information about feature points is based on the nearest 1-ring field points, which are usually the edge points of the face adjacent to the feature line. The high structural complexity of rigid aircraft components leads to recognition of false feature points. Therefore, this paper proposes an improved Harris algorithm designed to improve the accuracy of feature extraction. It combines the discrete curvature and the normal vector in a way that is suitable for use with point clouds. Key to this approach is the use of changes in the gradient rather than changes in the curvature to identify corner, plane, and crease points. Our method accurately eliminates pseudo-feature points that are too close to actual feature points in order to refine potential feature points. We demonstrate the efficiency and robustness of the proposed method by validating it against standard models and actual scan data and by comparing it with other feature detection algorithms.