Xinfang Huang

Xinfang Huang

Auto-generated profile, based on publicly available information

Xinfang Huang

School of Mechanical Engineering and Automation, University of Science and Technology Liaoning, Anshan 114051, China

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
WFwenqi fu
wenqi fu
SLShuang Liu
Shuang Liu
JJJun Jiao
Jun Jiao
ZXZhiwen Xie
Zhiwen Xie
XHXinfang Huang
Xinfang Huang
GMGuowu Ma
Guowu Ma
Cobalt–chromium (Co-Cr) alloys have been widely used as dental-restoration materials for many years. This study sought to investigate whether selective laser melting (SLM) is a more appropriate process than traditional casting (CAST) for fabricating dental Co-Cr alloys. Metallurgical microscopy, X-ray photoelectron spectroscopy (XPS), Vickers hardness and nanoindentation tests, and friction and wear tests were used to evaluate the microstructure, surface compositions, mechanical properties, and wear resistance, respectively. Additionally, the biocompatibilities and cell adhesion of the alloys were evaluated with L-929 fibroblasts via CCK-8 assay, Live/Dead staining, flow cytometric analysis, scanning electron microscopy (SEM) observation and real-time PCR (RT-PCR) assay. The XPS results showed that the two alloys were all mainly comprised of Co, Cr, and O. The hardness in the CAST group equaled 7.15 ± 0.48 GPa, while in the SLM group, it equaled 9.06 ± 0.49 GPa. The friction coefficient of SLM alloys remained at approximately 0.46, but the CAST specimens fluctuated significantly. SLM alloys exhibited shallower wear scars and less wear debris compared with CAST alloys, simultaneously. Additionally, there were higher survival and expression of cell-adhesion-related genes on SLM alloys of L-929 cells, which meant that the deleterious effect on L-929 cells was significantly reduced compared with that for the CAST alloys. Overall, the wear resistances and biocompatibilities of the Co-Cr dental alloys were dramatically affected by the fabrication technique. The SLM technique is advantageous over the CAST technique for fabricating Co-Cr dental alloys.

25 February 2020 in Coatings
Verified
Journal Article
Open access
PDF file
XHXinfang Huang
Xinfang Huang
ZXZhiwen Xie
Zhiwen Xie
KLKangsen Li
Kangsen Li
QCQiang Chen
Qiang Chen
YCYongjun Chen
Yongjun Chen
FGFeng Gong
Feng Gong
CrWN glass molding coatings were deposited by plasma enhanced magnetron sputtering (PEMS). The microstructure and thermal stability of these coatings were investigated by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscope, transmission electron microscope, atomic force microscope and nanoindentation tests. The as-deposited coating exhibited an aggravated lattice expansion resulting in a constant hardness enhancement. The vacuum annealing induced surface coarsening and the spinodal decomposition of the coating accompanied by the formation of nm-sized c-CrN, c-W2N, and h-WN domains. The annealed coating with low W content had mainly a face-centered cubic (f.c.c) matrix, strain fields caused by lattice mismatch caused hardness enhancement. Following an increase in W content, the annealed coating showed a mixed face-centered cubic (f.c.c) and hexagonal close-packed (h.c.p) matrix. The large volume fraction of h-WN phases seriously weakened the coating strengthening effect and caused an obvious drop in hardness.

26 December 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KLKangsen Li
Kangsen Li
GXGang Xu
Gang Xu
XHXinfang Huang
Xinfang Huang
ZXZhiwen Xie
Zhiwen Xie
FGFeng Gong
Feng Gong
Micro embossing is an effective way to fabricate a polymethyl methacrylate (PMMA) specimen into micro-scale array structures with low cost and large volume production. A new method was proposed to fabricate a micro-lens array using a micro-electrical discharge machining (micro-EDM) mold. The micro-lens array with different shapes was established by controlling the processing parameters, including embossing temperature, embossing force, and holding time. In order to obtain the friction coefficient between the PMMA and the mold, ring compression tests were conducted on the Shenzhen University’s precision glass molding machine (SZU’s PGMM30). It was found that the friction coefficient between the PMMA specimen and the mold had an interesting change process with increasing of temperature, which affected the final shape and stress distribution of the compressed PMMA parts. The results of micro-optical imaging of micro-lens array indicated that the radius of curvature and local length could be controlled by adjusting the processing parameters. This method provides a basis for the fabrication and application of micro-lens arrays with low-cost, high efficiency, and mass production.