In this work, we report the design of ceramic lattices produced via additive manufacturing (AM) used to improve the overall performances of compact, high temperature heat exchangers (HXs). The lattice architecture was designed using a Kelvin cell, which provided the best compromise among effective thermal conductivity, specific surface area, dispersion coefficient and pressure loss, compared to other cell geometries. A material selection was performed considering the specific composition of the fluids and the operating temperatures of the HX, and Silicon Carbide (SiC) was identified as promising materials for the application. The 3D printing of a polymeric template combined with the replica method was chosen as the best manufacturing approach to produce SiC lattices. The heat transfer behaviour of various lattice configurations, based on the Kelvin cell, was determined through computational fluid dynamics (CFD). The results are used to discuss the application of such structures to compact high temperature HXs.
Single-tank thermal energy storage (TES) systems represent not only a valuable alternative to the most commonly exploited two-tank configuration in conventional concentrating solar power (CSP) plants, but also the most suitable solution for air-based solar systems. The first parabolic trough CSP pilot plant (3.9 MWth peak), which uses air as heat transfer fluid (HTF), has been constructed in Ait-Baha Morocco. An important characteristic of this plant is the integration of a 100 MWhth TES unit based on a packed bed of gravel as storage medium. The TES unit is designed for daily operating conditions of 10 h of charging followed by 4.5 h of discharging, at higher HTF mass flow rate, and 9.5 h of idle. The nominal charging and discharging temperatures are 570°C and 270°C respectively. A previously validated computational fluid dynamics (CFD) approach was followed to evaluate the thermo-fluid dynamics behavior of the TES unit under investigation subjected to a total of 5 pre-charging cycles, to reduce the initial transients of the system, followed by 60 consecutive cycles. The TES performance was also evaluated on the basis of the first- and the second-law of thermodynamics. According to the simulation results, despite a relatively weak thermal stratification was observed into the packed bed, the TES performance showed an increase with cycles from 52% and 63% up to stable values of 90% and 88% for the energy and the exergy efficiencies respectively.
The development of an innovative and highly efficient heat exchanger (HE) solution for gas–gas heat recovery is one of the major objectives of the HYDROSOL-beyond project which aims at enhancing the process efficiency for producing hydrogen from water dissociation with concentrated sunlight. Because of the very high temperature level of the process (up to 1400 °C), an innovative ceramic HE design was proposed with an integrated lattice structure, as secondary surface, to maximize the heat transfer. To assist the design of the HE, a multiscale approach was adopted: a 1D model based on global correlations was developed and a 3D computational fluid dynamics model of the secondary surfaces were generated. The former was applied to assess the performance of the entire HE; while, the latter was exploited to study in detail the thermo-fluid dynamics behavior of a HE core element and to provide the global correlations to be integrated into the 1D model. In this work, the effect of several parameters and operating conditions, namely, number of channels, number of lattice layers located into each channel, solid material exploited for the HE structure, parting plates thickness, heat transfer fluid velocity, radiation heat transfer and solid material emissivity, on the HE effectiveness are reported and accurately described. Furthermore, based upon the results obtained, guidelines on the HE design to maximize its performance are also provided.
In the last years, it has been experimentally proven that the precursors of synthetic fuels can be produced exploiting the thermochemical water and CO2 splittin
10 January 2024 in SolarPACES Conference Proceedings
The pressurized design of the Synhelion absorbing gas receiver concept has been presented. Despite its intrinsic increased design complexity, foreseen advantages such as receiver downscaling and more compact piping and insulation systems were the drivers for the initial development of the 250 kWth receiver design operating at high pressure (10 bar absolute). The latter was driven by the results of specific computational fluid dynamics (CFD) simulations aimed at evaluating the receiver thermo-fluid dynamics behaviour along with the relative performance. This paper shows the results of the two initial CFD simulations campaigns aimed at evaluating the effect, on the receiver performance, of the integration of absorbing inserts (i.e., a series of concentric disks specifically arranged into the cavity to capture the incoming concentrated solar radiation) and the position and shape of the inlet section of the heat transfer fluid. The simulations results allowed not only to evaluate the receiver performance, in terms of thermal efficiency, but also to observe some criticalities related to the motion of the HTF through the receiver.
24 November 2025 in SolarPACES Conference Proceedings
A big challenge consists in maximizing the thermal efficiency of volumetric solar receivers that are used to collect solar energy and heat-up a heat transfer fluid in renewable energy systems. Parametric studies provide an undisputed aid in early design stages and fast computational models are important to rapidly test novel configurations. In this paper, a comprehensive analysis to assess the accuracy and the computational load of 1D and 3D models compared to relevant literature data is presented. A 1D finite volume model and a 1D explicit model based upon the thermal resistance network are built by solving the solid and fluid energy balances and results are compared to accurate 3D CFD simulations of a solar receiver consisting of a silicon-carbide absorbing structure. The calculated air and solid temperatures are compared to literature findings on a receiver test geometry for different heat transfer fluid velocities. Results show that fast 1D models provide very accurate results with a maximum error of 2%-5% with respect to the reference in a computational time of few seconds, two order of magnitude lower than the one needed by accurate 3D CFD simulations.