Kevin L. Baker

Kevin L. Baker

Auto-generated profile, based on publicly available information

Kevin L. Baker

Lawrence Livermore National Laboratory 1 , Livermore, California 94550

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2020 in Physics of Plasmas
Verified
Journal Article
Open access
PDF file
DSD. B. Sinars
D. B. Sinars
MSM. A. Sweeney
M. A. Sweeney
CAC. S. Alexander
C. S. Alexander
DAD. J. Ampleford
D. J. Ampleford
TAT. Ao
T. Ao
EYE. P. Yu
E. P. Yu
Pulsed power accelerators compress electrical energy in space and time to provide versatile experimental platforms for high energy density and inertial confinement fusion science. The 80-TW “Z” pulsed power facility at Sandia National Laboratories is the largest pulsed power device in the world today. Z discharges up to 22 MJ of energy stored in its capacitor banks into a current pulse that rises in 100 ns and peaks at a current as high as 30 MA in low-inductance cylindrical targets. Considerable progress has been made over the past 15 years in the use of pulsed power as a precision scientific tool. This paper reviews developments at Sandia in inertial confinement fusion, dynamic materials science, x-ray radiation science, and pulsed power engineering, with an emphasis on progress since a previous review of research on Z in Physics of Plasmas in 2005.

5 February 2024 in Physical Review E
Verified
Journal Article
Closed access
PDF file
AKA. L. Kritcher
A. L. Kritcher
AZA. B. Zylstra
A. B. Zylstra
CWC. R. Weber
C. R. Weber
OHO. A. Hurricane
O. A. Hurricane
DCD. A. Callahan
D. A. Callahan
CWC. Wild
C. Wild
In this work we present the design of the first controlled fusion laboratory experiment to reach target gain G>1 N221204 (5 December 2022) [ Phys. Rev. Lett. 132, 065102 (2024)], performed at the National Ignition Facility, where the fusion energy produced (3.15 MJ) exceeded the amount of laser energy required to drive the target (2.05 MJ). Following the demonstration of ignition according to the Lawson criterion N210808, experiments were impacted by nonideal experimental fielding conditions, such as increased (known) target defects that seeded hydrodynamic instabilities or unintentional low-mode asymmetries from nonuniformities in the target or laser delivery, which led to reduced fusion yields less than 1 MJ. This Letter details design changes, including using an extended higher-energy laser pulse to drive a thicker high-density carbon (also known as diamond) capsule, that led to increased fusion energy output compared to N210808 as well as improved robustness for achieving high fusion energies (greater than 1 MJ) in the presence of significant low-mode asymmetries. For this design, the burnup fraction of the deuterium and tritium (DT) fuel was increased (approximately 4% fuel burnup and a target gain of approximately 1.5 compared to approximately 2% fuel burnup and target gain approximately 0.7 for N210808) as a result of increased total (DT plus capsule) areal density at maximum compression compared to N210808. Radiation-hydrodynamic simulations of this design predicted achieving target gain greater than 1 and also the magnitude of increase in fusion energy produced compared to N210808. The plasma conditions and hotspot power balance (fusion power produced vs input power and power losses) using these simulations are presented. Since the drafting of this manuscript, the results of this paper have been replicated and exceeded (N230729) in this design, together with a higher-quality diamond capsule, setting a new record of approximately 3.88MJ of fusion energy and fusion energy target gain of approximately 1.9.

1 July 2021 in Physics of Plasmas
Verified
Journal Article
Closed access
PDF file
AKA. L. Kritcher
A. L. Kritcher
AZA. B. Zylstra
A. B. Zylstra
DCD. A. Callahan
D. A. Callahan
OHO. A. Hurricane
O. A. Hurricane
CWC. Weber
C. Weber
MHM. Herrmann
M. Herrmann
HYBRID-E is an inertial confinement fusion implosion design that increases energy coupled to the hot spot by increasing the capsule scale in cylindrical hohlraums while operating within the current experimental limits of the National Ignition Facility. HYBRID-E reduces the hohlraum scale at a fixed capsule size compared to previous HYBRID designs, thereby increasing the hohlraum efficiency and energy coupled to the capsule, and uses the cross-beam energy transfer (CBET) to control the implosion symmetry by operating the inner (23° and 30°) and outer (44° and 50°) laser beams at different wavelengths ( Δ λ > 0). Small case to capsule ratio designs can suffer from insufficient drive at the waist of the hohlraum. We show that only a small amount of wavelength separation between the inner and outer beams ( Δ λ 1–2 Å) is required to control the symmetry in low-gas-filled hohlraums (0.3 mg/cm3 He) with enough drive at the waist of the hohlraum to symmetrically drive capsules 1180 μm in outer radius. This campaign is the first to use the CBET to control the symmetry in 0.3 mg/cm3 He-filled hohlraums, the lowest gas fill density yet fielded with Δ λ > 0. We find a stronger sensitivity of hot spot P2 in μm per Angstrom (40–50 μm/Å wavelength separation) than observed in high-gas-filled hohlraums and previous longer pulse designs that used a hohlraum gas fill density of 0.6 mg/cm3. There is currently no indication of transfer roll-off with increasing Δ λ , indicating that even longer pulses or larger capsules could be driven using the CBET in cylindrical hohlraums. We show that the radiation flux symmetry is well controlled during the foot of the pulse, and that the entire implosion can be tuned symmetrically in the presence of the CBET in this system, with low levels of laser backscatter out of the hohlraum and low levels of hot electron production from intense laser–plasma interactions. Radiation hydrodynamic simulations can accurately represent the early shock symmetry and be used as a design tool, but cannot predict the late-time radiation flux symmetry during the peak of the pulse, and semi-empirical models are used to design the experiments. Deuterium–tritium (DT)-layered tests of 1100 μm inner radius implosions showed performance close to expectations from simulations at velocities up to ∼360 km/s, and record yields at this velocity, when increasing the DT fuel layer thickness to mitigate hydrodynamic mixing of the ablator into the hot spot as a result of defects in the ablator. However, when the implosion velocity was increased, mixing due to these defects impacted performance. The ratio of measured to simulated yield for these experiments was directly correlated with the level of observed mixing. These simulations suggest that reducing the mixing, e.g., by improving the capsule defects, could result in higher performance. In addition, future experiments are planned to reduce the coast time at this scale, delay between the peak compression and the end of the laser, to increase the hot spot convergence and pressure. To reduce the coast time by several hundred ps compared to the 1100 μm inner radius implosions, HYBRID-E has also fielded 1050 μm inner radius capsules, which resulted in higher hot spot pressure and a fusion energy yield of ∼170 kJ.

1 September 2020 in Physics of Plasmas
Verified
Journal Article
Closed access
PDF file
AZA. B. Zylstra
A. B. Zylstra
DCD. T. Casey
D. T. Casey
AKA. Kritcher
A. Kritcher
LPLouisa Pickworth
Louisa Pickworth
BBB. Bachmann
B. Bachmann
OHO. A. Hurricane
O. A. Hurricane
Mix of high-Z material from the capsule into the fuel can severely degrade the performance of inertial fusion implosions. On the Hybrid B campaign, testing the largest high-density-carbon capsules yet fielded at the National Ignition Facility, several shots show signatures of high levels of hot-spot mix. We attribute a ∼ 40 % yield degradation on these shots to the hot-spot mix, comparable to the level of degradation from large P2 asymmetries observed on some shots. A range of instability growth factors and diamond crystallinity were tested and they do not determine the level of mix for these implosions, which is instead set by the capsule quality.

1 January 2007 in Optics Express
Verified
Journal Article
Closed access
PDF file
KBK. L. Baker
K. L. Baker
MMM. M. Moallem
M. M. Moallem
Several techniques have been used with Shack-Hartmann wave-front sensors to determine the local wave-front gradient across each lenslet. In this article we introduce an iterative weighted technique which is specifically targeted for open-loop applications such as aberrometers and metrology. In this article the iterative centroiding technique is compared to existing techniques such as center-of-mass with thresholding, weighted center-of-gravity, matched filter and cross-correlation. Under conditions of low signal-to-noise ratio, the iterative weighted centroiding algorithm is demonstrated to produce a lower variance in the reconstructed phase than existing techniques. The iteratively weighted algorithm was also compared in closed-loop and demonstrated to have the lowest error variance along with the weighted center-of-gravity, however, the iteratively weighted algorithm removes the bulk of the aberration in roughly half the iterations than the weighted center-of-gravity algorithm. This iterative weighted algorithm is also well suited to applications such as guiding on telescopes.

1 May 2020 in Physics of Plasmas
Verified
Journal Article
Open access
PDF file
PPP. K. Patel
P. K. Patel
PSP. T. Springer
P. T. Springer
CWC. R. Weber
C. R. Weber
LJL. C. Jarrott
L. C. Jarrott
OHO. A. Hurricane
O. A. Hurricane
MEM. J. Edwards
M. J. Edwards
We describe the overall performance of the major indirect-drive inertial confinement fusion campaigns executed at the National Ignition Facility. With respect to the proximity to ignition, we can describe the performance of current experiments both in terms of no-burn ignition metrics (metrics based on the hydrodynamic performance of targets in the absence of alpha-particle heating) and in terms of the thermodynamic properties of the hotspot and dense fuel at stagnation—in particular, the hotspot pressure, temperature, and areal density. We describe a simple 1D isobaric model to derive these quantities from experimental observables and examine where current experiments lie with respect to the conditions required for ignition.