Hendrik Hemmelmann

Hendrik Hemmelmann

Auto-generated profile, based on publicly available information

Hendrik Hemmelmann

Center for Materials Research Justus‐Liebig‐University Gießen Heinrich‐Buff‐Ring 16 35392 Gießen Germany

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 January 2020 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
RRRaffael Ruess
Raffael Ruess
SSSimon Schweidler
Simon Schweidler
HHHendrik Hemmelmann
Hendrik Hemmelmann
GCGioele Conforto
Gioele Conforto
ABAnja Bielefeld
Anja Bielefeld
JJJürgen Janek
Jürgen Janek
In liquid electrolyte-type lithium-ion batteries, Nickel-rich NCM (Li1+x (Ni1−y−z Co y Mnz)1−x O2) as cathode active material allows for high discharge capacities and good material utilization, while solid-state batteries perform worse despite the past efforts in improving solid electrolyte conductivity and stability. In this work, we identify major reasons for this discrepancy by investigating the lithium transport kinetics in NCM-811 as typical Ni-rich material. During the first charge of battery half-cells, cracks form and are filled by the liquid electrolyte distributing inside the secondary particles of NCM. This drastically improves both the lithium chemical diffusion and charge transfer kinetics by increasing the electrochemically active surface area and reducing the effective particle size. Solid-state batteries are not affected by these cracks because of the mechanical rigidity of solid electrolytes. Hence, secondary particle cracking improves the initial charge and discharge kinetics of NCM in liquid electrolytes, while it degrades the corresponding kinetics in solid electrolytes. Accounting for these kinetic limitations by combining galvanostatic and potentiostatic discharge, we show that Coulombic efficiencies of about 89% at discharge capacities of about 173 mAh gNCM −1 can be reached in solid-state battery half-cells with LiNi0.8Co0.1Mn0.1O2 as cathode active material and Li6PS5Cl as solid electrolyte.

11 December 2022 in Small Science
Verified
Journal Article
Open access
DKDavid Kitsche
David Kitsche
YTYushu Tang
Yushu Tang
HHHendrik Hemmelmann
Hendrik Hemmelmann
FWFelix Walther
Felix Walther
MBMatteo Bianchini
Matteo Bianchini
Torsten BrezesinskiTorsten Brezesinski
Torsten Brezesinski
Protective coatings are required to address interfacial incompatibility issues in composite cathodes made from Ni‐rich layered oxides and lithium thiophosphate solid electrolytes (SEs), one of the most promising combinations of materials for high energy and power density solid‐state battery (SSB) applications. Herein, the preparation of conformal ZrO2 nanocoatings on a LiNi0.85Co0.10Mn0.05O2 (NCM85) cathode‐active material (CAM) by atomic layer deposition (ALD) is reported and the structural and chemical evolution of the modified NCM85 upon heat treatment—a post‐processing step often required to boost battery performance—is investigated. The coating properties are shown to have a strong effect on the cyclability of high‐loading SSB cells. After mild annealing (≈400 °C), the CAM delivers high specific capacities (≈200 mAh g−1 at C/10) and exhibits improved rate capability (≈125 mAh g−1 at 1C) and stability (≈78% capacity retention after 200 cycles at 0.5C), enabled by effective surface passivation. In contrast, annealing temperatures above 500 °C lead to the formation of an insulating interphase that negatively affects the cycling performance. The results of this study demonstrate that the preparation conditions for a given SE/CAM combination need to be tailored carefully and ALD is a powerful surface‐engineering technique toward this goal.

17 February 2023 in Advanced Materials Interfaces
Verified
Journal Article
Open access
HHHendrik Hemmelmann
Hendrik Hemmelmann
RRRaffael Ruess
Raffael Ruess
PKPhilip Klement
Philip Klement
JSJörg Schörmann
Jörg Schörmann
SCSangam Chatterjee
Sangam Chatterjee
MEMatthias Elm
Matthias Elm
Depositing ultrathin oxide coatings has been proven a successful approach to stabilize the surface of LiNixCoyMnzO2 active cathode material in lithium‐ion batteries (LIB). The beneficial effect of Al2O3 coatings arises at least partly from spontaneous reactions between coating and liquid electrolyte. However, it remains unclear if comparable surface reactions occur for other oxide coatings. One difficulty is the characterization of reaction products at the cathode–electrolyte interface due to the multi‐phase properties of composite cathodes. Here, thin films are utilized as model systems to correlate surface reactions with the performance of Al2O3‐ and CeO2‐coated nickel cobalt manganese oxides (NCM). Electrochemical characterization confirms that an Al2O3 coating improves long‐term cycling stability, while CeO2‐coated thin films perform even worse than uncoated counterparts. The analysis of the surface reaction products using X‐ray photoelectron spectroscopy shows that both coatings are fluorinated upon contact with liquid electrolyte in agreement with thermodynamic considerations. The fluorinated Al2O3 coating is stable during cycling, resulting in the improved cell performance. In contrast, the fluorinated CeO2 coating changes chemical composition, facilitating corrosion of the NCM surface. The results demonstrate the importance of a detailed analysis of surface reactions to evaluate the suitability of ultrathin oxide layers as protective coatings for LIBs.