This paper presents an improved synthetic loading method to measure the performance of an interior permanent magnet synchronous machine (IPMSM). A complete analysis of torque-, flux-, and efficiency-maps are done by means of a vector controlled drive implemented with in a field programmable gate array (FPGA). The measurements are compared to results from Finite Element Analysis (FEA). A key feature of this implementation is an instantaneous measurement of the inverter output voltage that facilitates estimation of the input power of the machine. The synthetic loading technique completely eliminates the need for a torque transducer, load machine and holds a control over temperature development during the tests. Simulation and experimental results demonstrate that the supply tracking together with synthetic loading technique is very useful tool to evaluate the efficiency of IPMSM.
A radical transformation of the transport industry is required in order to achieve a fossil-fuel-free vehicle fleet and reach the greenhouse gas emissions goals. Electrification plays a crucial role in this radical process. An electric road system (ERS) is a road that supplies power to electric vehicles as they drive on it, offering numerous advantages. These include an extended driving range, decreased reliance on batteries, and increased flexibility and convenience for drivers, eliminating the need to stop for recharging. This paper highlights the transformative potential of ERS in revolutionizing the land transport sector. Through thorough testing with a conductive ERS demonstrator, the viability of the presented technology is validated. Essential aspects like power transfer, efficiency, safety, and environmental impact showcase ERS’s adaptability and scalability across diverse vehicle types. This study recommends widespread ERS support for battery electric vehicles, emphasizing the route toward a sustainable future.
Enabling vehicles to draw energy from an electric road system (ERS) significantly reduces the need for battery capacity on board the vehicle. It is not necessary, nor realistic, to cover every meter of every stretch of road with ERS. The question then arises how and where the ERS sections should be placed. One way of doing it is to place equally long sections of ERS with a certain separating distance. Another way is to place the sections where the highest amount of traction power of the vehicles is required. This paper presents a performance evaluation of both these methods from an energy consumption and battery degradation point of view. This study assumes a conductive ERS which allows for high power transfer. Being conductive, galvanic isolation between the energy source (the ERS) and the on board traction voltage system (TVS) is needed for electric safety reasons. In addition to the two alternative methods for location of ERS segments, three different powertrains, each with a different approach to galvanic isolation and charging, are evaluated. It is discovered that the method for location of the ERS can in fact affect both energy consumption and battery degradation depending on powertrain and driving scenario.
Conductive Electric Road Systems (ERS) appear as a promising solution for the electrification of transportation, particularly for heavy vehicles and long-distance trips but also for light vehicles. Significant research efforts are currently devoted to the development of conductive ERS systems, with up to four pilot test sites with different technologies in operation only in Sweden. With the help of electric models and experimental measurements on a pilot test track, this article assesses the potential safety challenges associated with one aspect of this technology: the absence of a reliable protective earth connection while the vehicle is connected to the ERS power supply. The results highlight the importance of monitoring the chassis potential at all times and the need of an active safety mechanism to disconnect the vehicle from the ERS supply if a severe fault occurs.
One of the main challenges as the market for fully commercial electrified vehicles quickly expands is predicting the electromagnetic interference (EMI) in traction voltage systems (TVSs) in differential mode (DM) and common mode (CM). The number of subsystems connected to vehicle TVSs is increasing, and thus, so are the electromagnetic compatibility (EMC) requirements. These requirements should make sure that neither the function nor lifetime of any source or load is affected by another, but experience shows that they are often insufficient. The purpose of this article is to show how circuit simulations can complement these requirements and that a generalized artificial network/line impedance stabilization network (LISN) is insufficient to correctly predict the EMI situation of a real vehicle. This article presents a method for complexity reduction in TVS DM simulations and a comparison with the usage of LISN to predict the EMI between subsystems; the article also addresses how to mitigate the EMI with DM filters for the subsystems. The proposed method creates a foundation for a faster and safer development process. The simulation model’s development includes a traction battery and TVS subsystems. It is found that a standardized LISN does not reflect the behavior of a commercial TVS and cannot be used solely to judge if a subsystem will operate as intended within a TVS without creating EMI. A change in switching frequency in the DUT can cause severe resonance between TVS subsystems, but this is not seen with a LISN. The conclusion of the article is that LISN can provide a false sense of security and that calibrated simulation models of a complete TVS are necessary to predict the behavior in that TVS; this study also highlights the importance of using DM filters to ensure protection against resonance frequencies.
At present, the prevalence of electric vehicles is increasing continuously. In particular, there are promising applications for commercial vehicles transferring from conventional to full electric, due to lower operating costs and stricter emission regulations. Thus, cost analysis from the fleet perspective becomes important. The study of cost competitiveness of different drivetrain designs is necessary to evaluate the fleet cost variance for different degrees of electrical machine commonality. This paper presents a methodology to find a preliminary powertrain design that minimizes the Total Cost of Ownership (TCO) for an entire fleet of electric commercial vehicles while fulfilling the performance requirements of each vehicle type. This methodology is based on scalable electric machine models, and particle swarm is used as the main optimization algorithm. The results show that the total cost penalty incurred when sharing the same electrical machine is small, therefore, there is a cost saving potential in higher degrees of electrical machine commonality.