Electric Road Systems (ERS) have emerged as an alternative to deal with the main drawbacks that battery electric vehicles present (i.e., higher cost, short driving range, long charging times, etc.). This paper analyses the societal cost of electrifying all road transport in Denmark under four different scenarios. The first scenario considered in this study is based on today’s approach of having electric vehicles with high battery capacity and fast charging stations, the remaining scenarios study the cost of implementing different ERS at a national level. The results clearly show the benefits of implementing road bound electric road solutions that can be used both by commercial and passenger vehicles.
This paper presents an improved synthetic loading method to measure the performance of an interior permanent magnet synchronous machine (IPMSM). A complete analysis of torque-, flux-, and efficiency-maps are done by means of a vector controlled drive implemented with in a field programmable gate array (FPGA). The measurements are compared to results from Finite Element Analysis (FEA). A key feature of this implementation is an instantaneous measurement of the inverter output voltage that facilitates estimation of the input power of the machine. The synthetic loading technique completely eliminates the need for a torque transducer, load machine and holds a control over temperature development during the tests. Simulation and experimental results demonstrate that the supply tracking together with synthetic loading technique is very useful tool to evaluate the efficiency of IPMSM.
The focus of this paper is on the development of a single phase PM machine with wave-windings where the design variables are the winding layout and design of a soft magnetic powder core for a stator. A number of BH curves are synthesized in order to characterize some of the existing powder cores and to study the influence of magnetic permeability on starting torque and mean driving torque. The goal of the wave-winding design is to increase the material utilization factor and minimize the resistive power losses in the winding of a radial-to-transversal flux machine with an iron powder core. The outcomes of this paper is a 3D FE magnetic analysis of a number of suggested stator layouts supported with a rapid prototype with a dummy coil.
A design model development for electrical machines with laminated windings is presented. The focus is to provide manufacturable solutions for commercial vehicle traction applications. The machine is designed with axially distributed single-layer wave-winding segments with a core that builds a modular three-phase machine. The phase segment, whose central part is a wave-winding made as a laminated winding, form a semi-claw pole structure. A conventional permanent magnet synchronous machine is used as a reference. The result indicates that comparable torque and power can be reached with the suggested alternative design.
The objective of this paper is to evaluate a single-phase claw pole machine where the magnetic core is made of a soft magnetic mouldable composite material (SM 2 C). SM 2 C has low permeability but also very low remagnetization losses, which makes this kind of material very suitable for high frequency applications. Therefore, the high speed characteristics of the single-phase claw-pole machine are in focus on theoretical analysis and practical evaluations.
This article focuses on the analysis of a direct air-cooled rotor winding of a wound field synchronous machine, the innovation of which lies in the increase in the internal cooling surface, the cooling of the winding compared to the conventional inter-pole cooling, and the development of a CHT evaluation model accordingly. Conjugate heat transfer (CHT) analysis is used to explore the cooling efficacy of a parallel-cooled hollow-conductor winding of a salient-pole rotor and to identify a cooling performance map. The use of high current densities of 15–20 Arms/mm2 in directly cooled windings requires high cooling intensity, which in the case of air cooling results not only in flow velocities above 15 m/s to ensure permissible operating temperatures, but also the need for coolant distribution and heat transfer studies. The experiments and calculations are based on a non-rotating machine and a wind tunnel using the same rotor coil(s). CHT-based thermal calculations provide not only reliable results compared to experimental work and lumped parameter thermal circuits with adjusted aggregate parameters, but also insight related to pressure and cooling flow distribution, thermal loads, and cooling integration issues that are necessary for the development of high power density and reliable electrical machines. The results of the air-cooling integration show that the desired high current density is achievable at the expense of high cooling intensity, where the air velocity ranges from 15 to 30 m/s and 30 to 55 m/s, distinguishing the air velocity of the hollow conductor and bypass channel, compared to the same coil in an electric machine and a wind tunnel at the similar thermal load and limit. Since the hot spot location depends on cooling integration and cooling intensity, modeling and estimating the cooling flow is essential in the development of wound-field synchronous machines.