Zhuang Wu

Zhuang Wu

Auto-generated profile, based on publicly available information

Zhuang Wu

School of Power and Energy, Northwestern Polytechnical University, Xi'an 710072, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 June 2023 in Applied Thermal Engineering
Verified
Journal Article
Closed access
XWXin-Yu Wang
Xin-Yu Wang
CLCun-Liang Liu
Cun-Liang Liu
HZHui-Ren Zhu
Hui-Ren Zhu
XBXiao-Hui Bai
Xiao-Hui Bai
ZWZhuang Wu
Zhuang Wu
ZWZi-Wen Wang
Zi-Wen Wang

27 March 2024 in Energy
Verified
Journal Article
Closed access
ZXZhi-Peng Xu
Zhi-Peng Xu
CLCun-liang Liu
Cun-liang Liu
LYLin Ye
Lin Ye
HZHui-Ren Zhu
Hui-Ren Zhu
ZWZhuang Wu
Zhuang Wu

22 February 2022 in Applied Thermal Engineering
Verified
Journal Article
Closed access
ZWZhuang Wu
Zhuang Wu
HZHui-Ren Zhu
Hui-Ren Zhu
CLCun-Liang Liu
Cun-Liang Liu
XLXu-Yang Liu
Xu-Yang Liu
ZZZheng Zhang
Zheng Zhang

4 January 2022 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
ZWZhuang Wu
Zhuang Wu
HZHui-Ren Zhu
Hui-Ren Zhu
CLCun-liang Liu
Cun-liang Liu
LLLin Li
Lin Li
MWMing-Rui Wang
Ming-Rui Wang
To investigate the superposition effect of the leading edge (LE) film on the downstream film cooling under swirling inflow, numerical simulations with three vane models (vane with films on the leading edge only, vane with films on the pressure side (PS), and suction side (SS) only, full-film cooling vane), two inlet conditions (axial inlet and swirling inlet) are conducted. The results indicate that the leading edge is the area where the film is most affected by the swirling inflow. For full-film cooling vane, the film on the leading edge does not always improve or even reduce the downstream film cooling. Flow mechanism analysis shows that the velocity direction near the downstream wall is governed by the interaction between the direction of swirling inflow and the direction of film hole incidence on the leading edge. A new type of leading-edge film proposed by the author is also investigated, with the dividing line of the counterinclined film-hole row coinciding with the twisted stagnant line to ensure that all films are incident at angles inverse to the direction of the swirling inflow. The new leading-edge film successfully changes the velocity direction near the downstream wall and suppresses the deflecting effect on the downstream film. The new leading-edge film can increase the overall area-averaged cooling effectiveness (η) of the full-film cooling vane by 10%, 15%, 18% and reduce the inhomogeneity by 13%, 19%, 27% over the traditional design, as the coolant mass flow increases.

10 March 2021 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Verified
Journal Article
Closed access
PDF file
ZWZhuang Wu
Zhuang Wu
HZHui-Ren Zhu
Hui-Ren Zhu
CLCun-Liang Liu
Cun-Liang Liu
LLLin Li
Lin Li
XLXu-Yang Liu
Xu-Yang Liu
The heat transfer performance of showerhead film cooling on the vane leading edge was numerically investigated considering representative lean burn combustor swirling outflow. Three cases with different inflow conditions (uniform inflow, positive swirling inflow, and negative swirling inflow) and three cases with different film injection angles (45°, 90°, and 135°) were studied. As the first study to explore the showerhead film design principle under swirling inflow, a newly designed asymmetrical counter-inclined (45° and 135°) film cooling was also proposed. To examine the design principles, the cooling effectiveness, heat transfer augmentation, and heat flux reduction of the newly designed asymmetrical case were evaluated compared with the traditional symmetrical case. The results show that the swirling inflow introduces obvious radial pressure gradient on the vane. The radial pressure gradient is the key influence factor to deflect the coolant migration, decrease the cooling effect, and degrade the homogeneity. The film with opposite orientation to the radial pressure gradient can weaken the deflect effect. The radial pressure gradient direction differs in different regions, making it impossible for the film with congruent injection orientation to simultaneously resist the pressure gradient on the entire vane. For the new design, the boundary line of the counter-inclined holes is consistent with the twisted stagnation line to guarantee that the injection orientation of all the film holes is opposite to the radial pressure gradient. As expected, the new design can effectively weaken the deflection effect and show uniform film distribution. The higher coolant mass ratio provides more obvious enhancement effect. At coolant mass ratio 3.71% and 4.56%, the overall area-averaged heat flux reduction (Δq) is increased by 0.311 and 0.576, and the overall area-averaged relative standard deviation is reduced by 12.17 and 11.66 compared with the traditional design. The results have confirmed the adaptability of the film design principle under swirling inflow.

16 November 2020 in Journal of Heat Transfer
Verified
Journal Article
Closed access
PDF file
LLLin Li
Lin Li
CLCun-liang Liu
Cun-liang Liu
BLBing-Ran Li
Bing-Ran Li
HZHui-Ren Zhu
Hui-Ren Zhu
ZWZhuang Wu
Zhuang Wu
WCWen-Bin Chen
Wen-Bin Chen