In this research, orthogonal array of L27 in Taguchi Method was used to optimize the process parameters (control factors) variation in 45nm n-channel device with considering the interaction effect. The signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are employed to study the performance characteristics of the device. There are only five process parameters (control factors) were varied for 3 levels to performed 27 experiments. Whereas, the two noise factors were varied for 2 levels to get four readings of Vth for every row of experiment. In this study, nominal-the-best characteristic was used in an effort to minimize the variance of Vth. The results show that the Vth values have least variance and percent different from the target value (0.287V) for this device is 1.42% (0.293V). This value is closer with International Technology Roadmap for Semiconductor (ITRS) prediction.
1 February 2025 in Bulletin of Electrical Engineering and Informatics
This article proposes an optimization method to predictively model the perovskite solar cell with molybdenum disulfide (MoS2) based inorganic hole transport material (HTM) for improved fill factor (FF) and power conversion efficiency (PCE) by finding the most optimum thickness and donor/acceptor concentration for each layer via a hybrid L27 Taguchi grey relational analysis (GRA) based genetic algorithm (GA). Numerical simulation of the device is carried out by employing one-dimensional solar cell capacitance simulator (SCAPS-1D) while the optimization procedures are developed based on combination of multiple methods; L27 Taguchi orthogonal array, GRA, multiple linear regression (MLR), and GA. The results of post-optimization reveal that the most optimum layer parameters for improved FF and PCE are predicted as follows; SnO2F thickness (0.855 μm), SnO2F donor concentration (9.206×1018 cm-3), TiO2 thickness (0.011 μm), TiO2 donor concentration (9.306×1016 cm-3), CH3NH3PbI3 thickness (0.897 μm), CH3NH3PbI3 donor concentration (0.906×1013 cm-3), MoS2 thickness (0.154 μm), and MoS2 acceptor concentration (9.373×1017 cm-3). Both FF and PCE of the device are improved by ~1.1% and ~12.6% compared to the pre-optimization.
1 December 2024 in Bulletin of Electrical Engineering and Informatics
The study proposes a novel approach for detecting adulteration in edible oils utilising a zinc oxide (ZnO)-coated optical sensor. The procedure included the development of a sensor probe using a plastic optical fiber (POF) with a ZnO nanolayer deposition. The ZnO nanorods were applied to the surface of the POF via a hydrothermal process. The sensitivity and accuracy of uncoated and ZnO-coated POFs were compared, and it was discovered that the ZnO-coated POF was more sensitive to changes in the refractive index of the samples under testing. The study ascertained a correlation between the optical power and voltage of the sensor and the refractive index of the medium. As the adulterant concentration in the oil mixture increased, the refractive index of the medium altered. As a result, both the sensor’s output voltage and optical power decreased. Upon completion, it was discovered that the uncoated POF had a sensitivity of 0.073 V/%, whereas the ZnO-coated POF had a sensitivity of 0.085 V/%. These findings highlight the effectiveness of ZnO-coated optical sensors, as well as their potential integration into internet of things (IoT) platforms for monitoring adulteration in edible oils.
15 April 2020 in Malaysian Journal of Fundamental and Applied Sciences
In this paper, we report a comparative study of fiber optic sensors for the application of aqueous solutions concentration monitoring. A simple, economical, and efficient set-up for liquid concentration measurement system was developed using polymer optical fibers (POFs). Cornstarch, sucrose, and salt solutions with different concentrations were tested, and the output power and the refractive index obtained were compared. The sensitivity of the sensor is found ranging from 0.938 μW/ RIU to 96.9 μW/RIU in term of refractive index change and 0.04298 μW/molL-1 to 0.097 μW/molL-1 in terms of concentration. It has been found that the concentration is proportionally related to its refractive index where high refractive index will experience greater loss since the light rays tend to be refracted out of the fiber instead of being internally reflected. The experimental results also show that as the solution’s concentration increases, the output power decreases.
High-k dielectric insulators are required to reduce leakage and increase transistor performance. They are able to impact the mobility of carriers in transistors positively, leading to better device performance in advanced transistor architecture. Nevertheless, an in-depth analysis of how high-k dielectric insulators influence transistor characteristics must be carried out to determine their suitability. The objective of this study is to investigate the impact of high-k insulators towards electrical properties of junctionless double gate strained transistor. The simulation works is done using process/device simulator Silvaco Athena/Atlas. Based on the retrieved results, the magnitude of ION, on-off ratio, gm, and Cint for TiO2-based device are approximately 63%, 99%, 62%, and 89% respectively higher than the lowest permittivity material-based device. The TiO2-based device also exhibits the lowest magnitude in IOFF and SS compared to others. However, a significant degradation in fT magnitude have been observed for TiO2-based device significantly due to its large capacitances