18 January 2025 in The European Physical Journal Plus
Batteries are one of the most important systems in electric vehicles. The performance of batteries varies depending on temperature, and high battery temperatures reduce battery efficiency and life. In recent years, intensive studies have been carried out on passive systems to prevent the battery module from heating, and many studies have been conducted especially on the use of phase change material (PCM). In this study, a novel battery module design created using PCM is tested by setting up experimental setups at both different discharge rates and different ambient temperatures, and the cooling performance of PCM is examined. As a result, it was found that the temperature increase in the PCM decreases during the melting process and the increase in the battery surface temperature varies according to the current value of the total heat generated in the battery. If the total heat generated in the battery increases, both the battery surface temperature and the temperature rise rate increase; if the total heat generated in the battery is constant or decreasing, the battery surface temperature increases but the temperature rise rate decreases.
28 March 2024 in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
Isı pompaları, binalarda soğutma ve ısıtma için kullanılan konvansiyonel sistemlere verimli ve ulaşılabilir alternatiflerdir. Isı kaynağı olarak toprak ısısını kullanan toprak kaynaklı ısı pompaları (TKIP), ısıtma ve soğutma yüklerini temiz ve sürdürülebilir bir şekilde karşılamak için umut verici teknolojilerdir. TKIP, kurulum ve işletme maliyetleri yüksek olan bir sistemdir. Bu nedenle verimlilik açısından farklı sektörlerde kullanımı uygun olan TKIP sistemini kurmadan performans analizleri yapılabilir olması çok önemlidir. Sistemler kurulmadan önce performans değerlerinin tahmin edilebilecek olduğu modeller ile değerlendirilmesi yaklaşımdan yola çıkılarak, ısı pompası ve sistemin performansı ve yoğuşturucudan atılan ısıyı tahmin etmek için bir yapay sinir ağı (YSA) modeli önerilmektedir. Yapay sinir ağları ile regresyon analizi, girdi ve çıkış verileri arasındaki karmaşık ilişkileri öğrenme yeteneğine sahip bir makine öğrenimi yöntemidir ve problemlerindeki non-lineer ilişkileri etkili bir şekilde modelleyebilir. Sivas ilinde Kurulan deneysel sistem ile ölçülen veriler, YSA'yı eğitmek için eğitim verisi ve test verisi olarak ayrılmıştır ve modelin ilk aşamasında eğitim verisi; ikinci aşamasında ise test verisi kullanılmıştır. Sunulan çalışmada, yatay TKIP’ın performans katsayısını tahmin etmek için çeşitli uygulamalarda kullanılmış ve özellikle sistem modelleme ve sistem tanımlamada yararlı oldukları gösterilmiş yapay sinir ağlarının uygulanabilirliği ortaya konulmuştur. Bu çalışmanın sonucunda, ısı pompası COP R2 değeri 0,9733, TKIP sistemi COP R2 değeri 0,9896 ve yoğuşturucudan atılan ısının YSA modelinin R2 değeri 0,9878 olduğu tespit edilmiştir. Üretilen istatistiksel belirleyiciler üzerinden yola çıkılarak YSA'ların TKIP sisteminde doğru bir yöntem olarak COP tahmini için kullanılabileceği sonucuna varılmıştır.
1 December 2019 in Journal of Polytechnic
Bu deneysel çalışmada yatay toprak kaynaklı ısı pompası iki odadan oluşan toplam 51.3 m3 hacme uygulanarak, Sivas ili şartlarında ısıtma ve soğutma için performans analizi araştırılmıştır. Kış ve yaz aylarında gerçekleştirilen ölçümlerde; ısıtma ve soğutma için sırasıyla tipik bir kış/yaz günü olan 16 Aralık ve 29 Haziran tarihlerinde elde edilen değerler kullanılmıştır. Bu şekilde toprak kaynaklı ısı pompası uygulamasının Sivas iline ait davranış özelliklerinin belirlenmesi amaçlanmıştır. İç ve dış ortam sıcaklıkları, 4 farklı derinlikte ölçülmüş toprak sıcaklıkları ve ısı pompası elemanlarının giriş çıkış sıcaklıkları kayıt altına alınmıştır. Ölçülen veriler sistem ve ısı pompasına ait performans katsayısı değerlerini hesaplamada kullanılmıştır. Deneysel veriler kullanılarak ısıtma modunda ortalama performans katsayısı değerleri ısı pompası ve sistem için sırasıyla 2.10 ve 1.83, soğutma modunda ise ısı pompası için ortalama 4.79 ve sistem için ortalama 3.86 olarak hesaplanmıştır. Ayrıca ısı pompası için ısıtma güç tüketimi ortalama değeri 2.83 kW, soğutma güç tüketimi ortalama değeri 1.69 kW olarak elde edilmiştir.
9 October 2024 in The European Physical Journal Plus
31 December 2025 in Bitlis Eren University Journal of Science and Technology
The study involved a series of experiments to examine the heat transfer behaviour of shell-and-tube heat exchangers with a helically coiled corrugated tube. Experimental investigations were conducted to analyse the performance of the heat exchangers, with a focus on the impact of tube- and shell-side flow rates, as well as shell inlet temperature, on effectiveness. Throughout the experiments, the tube inlet water temperature was kept at 20 °C, whereas the shell inlet temperature was set to 50, 60 or 70 °C. The tube flow rate was set to 1, 2 or 3 L/min, while the shell flow rate was set to 2, 3 or 4 L/min. A total of 27 tests were performed with these combinations. The results show that effectiveness increases significantly with an increase in the shell side flow rate and hot inlet water temperature, whereas an increase in the tube side flow rate reduces effectiveness. The highest effectiveness value (ε = 0.603) was obtained at a shell side flow rate of 4 L/min, a tube side flow rate of 1 L/min and a shell side inlet temperature of 70 °C. The maximum heat transfer was measured as 3290 W at an inlet temperature of 70 °C and a flow rate of 4 L/min on the shell side and 3 L/min on the tube side. The experimental data obtained provide a reliable basis for validating numerical models and designing highly efficient, compact heat exchangers.
30 December 2025 in Sivas Cumhuriyet Üniversitesi Mühendislik Fakültesi Dergisi
In this study, a 2-D numerical analysis was conducted the melting characteristics of phase change material (PCM) placed inside the container formed by using rectangular flat fins and to evaluate its effect on the average surface temperature of the PV panel accordingly. Flat fins were used in this study for the purpose of improving heat transfer and thermal enhancement in the latent heat storage system. To produce a two-dimensional analysis of the one-hour experimental study carried out under laboratory conditions, melting fraction, the temperature distribution and flow fields of the PCM were shown using ANSYS Fluent 18.2 software. The experimental results obtained from the previous study and the analysis results carried out in this study were quite similar and the difference between the average surface temperatures of the PV Panel was found to be 4.25%. In addition, the effects on the PV panel average surface temperature were observed by changing the initial ambient temperature and the amount of radiation.