15 May 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper proposes an integrated on-board charger (IOBC) for Electric Vehicles (EVs) based on an isolated three-port DC-DC converter. The proposed architecture integrates the on-board charger (OBC) and the auxiliary power module (APM) in a single multiport converter, offering low component count. The proposed converter is capable of charging high-voltage (HV) and low-voltage (LV) batteries simultaneously, over the entire battery voltage ranges. A three-winding transformer is used to provide galvanic isolation between the converter ports and consequently, power flow is coupled among the three ports. In this paper, a boundary condition is derived for the first time and a novel modulation scheme is proposed to regulate the power flow at the HV and LV ports independently, utilizing the converter’s 3-degrees-of-freedom (DOF). Hence, charging of the HV and LV batteries can be realized similar to dual-active-bridge (DAB) and phase-shifted full-bridge (PSFB) converter, respectively. Results show that all converter semiconductor devices operate with zero-voltage-switching (ZVS) over wide power and voltage range without the need of additional resonant components, due to the proposed 3-DOF selection scheme. A 3.5kW hardware prototype of the proposed converter is built and tested and key experimental results are presented to verify the converter theoretical analysis and ZVS operation.
25 December 2018 in IEEE Transactions on Power Electronics
A novel single-stage high frequency link three-phase inverter along with a modulation strategy is presented in this paper. The topology is targeted for grid integration of utility scale renewable and alternative energy sources like solar, fuel cell and wind, where the power flow is unidirectional (from DC to AC). The primary side converter has three-phase voltage source inverter (VSI) structure along with an additional half-bridge leg. Sinusoidal pulse width modulation is implemented in the primary side converter. The three legs of the primary side VSI are zero voltage switched (ZVS) for most part of the line cycle. The additional half bridge leg is zero voltage switched (ZVS) over the complete line cycle. The active switches in secondary side converter are line frequency switched and thus results in negligible switching loss. The converter switching process is described in detail to show the soft-switching of the primary side converter using the device capacitances and leakage inductances of the high frequency transformers. The high frequency transformer galvanic isolation results in high power density. A 4 kW laboratory scale hardware prototype is built and tested with the proposed modulation strategy. The experimental results are presented to verify the converter operation.
25 September 2019 in IEEE Transactions on Industrial Electronics
In this paper a pulse width modulated (PWM) single-stage high frequency link (HFL) three-phase DC-AC converter is proposed for grid integration of solar and fuel cell based energy sources. In the DC side, the converter has three half-bridge legs which are zero-voltage switched (ZVS) over the entire line cycle without using any additional snubber circuit. In the AC side, two diode bridge rectifiers and one neutral point clamped (NPC) T-type three-level inverter are employed. The active switches in NPC inverter are switched either at line frequency or twice of it, incurring negligible switching loss. Modulation ensures soft commutation in the diode bridges. The intermediate three level DC bus is pulsating and does not require any DC filter capacitor and thus reduces overall filtering requirements. The high frequency galvanic isolation provides high power density, low cost converter solution. The converter operation is analysed in detail and verified on a 2 kW hardware prototype.
19 August 2019 in IEEE Transactions on Power Electronics
This paper proposes a unidirectional, single-stage, three-phase, high-frequency-link (HFL) DC-AC converter. The converter uses three high frequency transformers (HFT) to provide galvanic isolation. In the primary, the converter has three half-bridge legs. In secondary three diode-bridge rectifiers are used. Each rectifier is followed by a half-bridge (unfolder) leg. The modulation strategy proposed in this paper ensures zero voltage switching (ZVS) of all six primary side switches over the entire line cycle without additional snubber circuit. The secondary half-bridge legs are switched at line frequency, incurring negligible switching loss. The proposed converter does not require any inter-stage bulky DC-link filter capacitor. Thus, the overall filtering requirement is reduced, and the converter reliability is improved. The high frequency galvanic isolation improves the converter power density. In the paper, the modulation strategy and converter operation are described in detail. The operation is validated in a 3.7 kW hardware prototype. Key experimental results are presented in the paper.
2 April 2020 in IEEE Transactions on Power Electronics
A three-level three-phase single-stage high-frequency link (HFL) DC-AC converter is reported in this paper for grid integration of photovoltaic sources. The proposed topology employs two three-level neutral point clamp (NPC) half-bridge legs on the DC side. The advantages of using three-level legs over conventional two-level are- (a) the three-level legs can be implemented with the devices with lower blocking voltage, (b) the low voltage blocking devices have lower on-state drop and lower turn ON-OFF energy losses compared to high voltage blocking devices used in a two-level leg. These help to improve the converter efficiency. The sinusoidal pulse width modulation is implemented with the three-level NPC legs. The inner switches of the NPC legs are zero voltage switched (ZVS). The turn ON transitions of the outer switches are with zero current (ZCS). The proposed solution employs two high-frequency transformers to provide galvanic isolation. The intermediate DC link is pulsating and does not require any filtering. A low-frequency unfolder is employed to generate line frequency AC from pulsating DC. The switching loss of the unfolder is negligible. The proposed topology can support stand-alone load upto $\pm 0.866$ PF. The converter operation is verified on a 2kW hardware prototype.