Photoelectrochemical (PEC) water splitting is a potentially promising route to direct solar-driven hydrogen production. Challenging targets for solar-to-hydrogen (STH) efficiency, durability, and semiconductor absorber costs must be realized for this approach to be economically competitive with other hydrogen production pathways. The first part of this talk will focus on the cost and performance metrics that go into techno-economic analysis and their status. Research on PEC hydrogen production at the National Renewable Energy Laboratory (NREL) has focused on III-V semiconductor absorber materials because their tunable bandgaps, high photon conversion efficiencies, and ability to make multi-junction structures that have resulted in the highest STH efficiencies yet demonstrated. However, to achieve the U.S. DOE’s hydrogen production target of $2/kg, in addition to high STH efficiency, the semiconductor absorber synthesis cost must come down 1-2 orders of magnitude from the current metal organic vapor phase epitaxial route. Hydride vapor phase epitaxy (HVPE) is a technique that has the potential to lower tandem III-V synthesis costs. The second part of this talk will describe experimental photoelectrochemical characterizations of HVPE-grown GaInP/GaAs tandem photoelectrodes with 1.85/1.38 eV bandgaps. Their incident photon-to-current efficiency, photocurrent vs. circuit bias, and unbiased chronoamperometry will be presented and discussed. Upon illumination, the HVPE-grown structures were able to drive water electrolysis spontaneously (e.g., without an external bias) at STH efficiencies up to 10%. The durability of III-V photoelectrodes remains an unresolved challenge for cost effective hydrogen production via photoelectrolysis.
Photo-electrochemical (PEC) hydrogen production is a route to carbon-free fuel that combines light absorption and water electrolysis into one device. Challenging targets for solar-to-hydrogen (STH) efficiency, durability, and semiconductor absorber costs must be realized for this approach to be economically competitive with other hydrogen production pathways. Research on PEC hydrogen production at the National Renewable Energy Laboratory (NREL) has focused on III-V semiconductor absorber materials because their tunable bandgaps, high photon conversion efficiencies, and ability to make multi-junction structures have resulted in the highest STH efficiencies yet demonstrated. This talk will focus on recent NREL results showing progress toward PEC hydrogen production efficiency, durability, and cost targets. Specifically, we have been able to improve theoretically achievable STH efficiency through bandgap engineering in multijunction devices. Photon management strategies to close the gap between theoretical and measured STH efficiency will also be discussed. Durability remains a significant challenge for III-V materials in a PEC environment. We will describe modifications to the semiconductor surface and the electrolyte constitution that can make the photoabsorber less susceptible to photocorrosion during operation. Finally, we will present preliminary results on III-V PEC materials synthesized via hydride vapor phase epitaxy, an alternative route to high-efficiency photoelectrodes that could potentially have much lower costs than the metalorganic vapor phase epitaxy method traditionally used. These improvements have yielded III-V PEC devices that are close to the STH efficiency target (17% vs. 25%) while the demonstrated durability and cost are still considerably far from their target values.
Ammonia synthesis from dinitrogen provides a critical feedstock to agriculture worldwide. The dominant process for ammonia synthesis, Haber-Bosch, is fossil-fuel dependent, energy intensive, and highly centralized. Electrochemical nitrogen reduction (ENRR) could provide a decentralized and environmentally friendly route to ammonia synthesis. ENRR research is challenging due to low amounts of ammonia produced in a typical experiment relative to environmental levels. In the first part of this presentation, we will share a critical result in ENRR experimental design which significantly improves the retention of generated ammonia, specifically related to the selection of membrane separators for H-cell or gas diffusion electrode cell platforms. This result is applicable to both dinitrogen and nitrate reduction research. In the second part of this presentation, a VS2-based ENRR catalyst, which has experimentally shown promising activity and selectivity, will be presented. Additionally, the proposed mechanism of ENRR on VS2 will be discussed, and we will discuss density functional theory simulation of ENRR on VS2 and MoS2. Finally, we will address areas of opportunity for ENRR.
Solution species govern crystallization pathways that define the morphology of metal halide perovskite thin films, making understanding their behavior essential for predicting film formation. Despite this importance, the structures of iodoplumbate species in widely used solvents, including N,N-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO), remain undetermined. Here, we combine optical absorption spectroscopy, X-ray scattering and spectroscopy, and atomistic simulations to demonstrate solvent coordination strength regulates iodide ligand sharing between Pb centers, thereby shaping iodoplumbate structure in lead iodide (PbI 2 ) and methylammonium lead iodide (MAPbI 3 ) inks. Weakly coordinating DMF promotes iodo(poly)plumbate formation (> 1 Pb 2+ per species), whereas DMSO stabilizes localized iodo(mono)plumbates. Molecular dynamics and computed absorption spectra attribute ~415 nm absorption in MAPbI 3 –DMF to the formation of short-lived polyplumbate structures. In situ GIWAXS connects these solvent-dependent solution populations to solvate intermediate formation during drying, establishing mechanistic insights for predicting and controlling perovskite crystallization through ink formulation.