This article proposes an output capacitor-less NMOS low-dropout regulator (LDO) using wide-range adaptive-gain nested Miller compensation (WAG-NMC) and pre-emphasis inverse (PI) biasing. Due to WAG-NMC, the LDO can provide a wide range of load current ( $I_{\mathrm{LOAD}}$ ) from 0.1 to 300 mA while maintaining sufficiently high phase margin (PM) above 60 $^{\circ}$ at all $I_{\mathrm{LOAD}}$ conditions. WAG-NMC also extends a loop bandwidth (BW) up to 17.5 MHz with using only small compensation capacitors ( $C_{\text{C}}$ ) of 6.3 pF in total. Moreover, PI biasing enhances a slew rate (SR) at the gate of the NMOS power transistor by injecting an adaptive PI current into a supersource follower (SSF), which further improves transient response. The proposed LDO fabricated in a 180-nm CMOS process was fully integrated with an on-chip load capacitor ( $C_{\text{L}})$ of 100 pF. The LDO ensures small undershoot and overshoot of 48 and 59 mV, respectively, against large $\Delta I_{\mathrm{LOAD}}$ of 299 mA due to wide-BW and high SR. The proposed LDO also achieves a best figure of merit (FoM) of 1.72 ps among the state of the arts.
29 November 2023 in IEEE Transactions on Power Electronics
This article proposes a hybrid always-dual-path recursive (ADPR) step-down converter to achieve high efficiency using a small-volume inductor with large dc resistance (DCR). The ADPR step-down converter utilizes only low-voltage transistors (1.5 or 3.3 V) for power switches. The converter has adopted adaptive switching level control, which includes adaptive mode transition (AMT) and adaptive duty modulation (ADM), based on one dual-flipped saw-tooth waveform. AMT and ADM enable a wide range operation and ensure flying capacitor charge balance while leading to higher efficiency. In addition, a complementary switch guarantees the reliable operation at lower input voltage to 2.8 V. The 130-nm prototype converter used a small-volume 4.7 μ H inductor with 288 mΩ DCR, a 10 μ F output capacitor, and two 4.7 μ F flying capacitors to verify highly efficient always-dual-path recursive operation. The measurement results show that the ADPR step-down converter can be suitable for converting Li-ion battery (2.8–4.2 V) to 0.7–1.1 V while the ratio of the inductor current over the load current ( I LOAD ) can be set between 0.42 and 0.66 at all range. The peak efficiency was measured up to 95.4% at V IN = 3.7 V and I LOAD = 75 mA. When V OUT = 1 V and I LOAD = 100 mA, the efficiencies were higher than 92.9% at whole input voltage ranges, ensuring small efficiency variation of 1.6%.
28 February 2024 in IEEE Transactions on Power Electronics
This article proposes a high-efficiency three-level boost converter that ensures reliable operation in wide input and output voltage ranges for light-emitting diode drivers. The proposed converter adopts robust auto calibration using half of the output voltage ( V OUT ) for flying capacitor voltage ( V CF ) self-balancing without requiring additional bulky feedback loops. In addition, the proposed dead-zone pulsewidth modulation control (DZPC) overcomes the limitations of irregular switching and output ripples near the duty 0.5 boundary by alternating between mode1 (D < 0.5) and mode2 (D > 0.5) at every cycle. The prototype converter was fabricated in a 180-nm Bipolar CMOS DMOS (BCD) process occupying a silicon area of 4.72 mm 2 while adopting a flying capacitor of 4.7 μ F and an inductor of 10 μ H. The peak efficiency was measured up to 96.3% at VIN = 24 V, VOUT = 30 V, and ILOAD = 100 mA. The proposed loop-free self-balancing verified the reliable three-level conversion regardless of duty by maintaining VCF at 0.5 VOUT , while DZPC also ensures efficient and seamless operation around the duty of 0.5.
15 December 2023 in IEEE Journal of Solid-State Circuits
This article proposes a single-inductor dual-output (SIDO) buck converter which always deliveries continuous power to outputs. The proposed converter has adopted complementary adaptive-switching regulation (CASR) with a continuous current balancing (CCB) mechanism and an auxiliary current path to passively bypass output switches in turn. The proposed converter and its control scheme can enhance output current continuities and power efficiencies while decreasing voltage ripples and fluctuations due to equivalent series resistance (ESR) and equivalent series inductance (ESL) at each output. The prototype converter was fabricated with the 180-nm CMOS process and comprises a 4.7- $\mu$ H inductor with 92-m $\Omega $ DCR, two 10- $\mu $ F output capacitors, and a 10- $\mu $ F capacitor for the auxiliary current path. The measured results verified that the always-power-delivered (APD) SIDO converter can generate 1.8 and 3.3 V from 5 V with a combined type-3 compensator (CT-3C), while providing continuous current to each output. The peak efficiency was 94.9% with the load conditions of 150 mA for 3.3 V and 75 mA for 1.8 V. In addition, the overall efficiencies were measured higher than 90% in all operation ranges.
Most old adults have mobility impairments because muscle weakness increases with age. Critically, stair ascent is one of the challenging tasks because the moments required at joints of the lower limb are significantly higher. In order to assist human anti-gravity movement, a soft wearable device with a tendon and pulleys system was designed. In this way, the device can support hip and knee extension simultaneously when the actuator is mounted on the upper body. Forces were measured by load cells at the lower limb, and the strategy was verified.
30 September 2024 in IEEE Transactions on Industrial Electronics
This article presents a scalable distributed linear regulator (SDLR) with on-chip output capacitor, which has 0.5–3.2% small current sharing error (96.8–99.5% current sharing accuracy) without using external components thanks to a replica-based current sharing calibrator. The proposed replica-based current sharing scheme offers significant benefits including low current consumption and universal design solutions for both low-voltage (LV) process and high-voltage (HV) process. Accordingly, the proposed SDLR can be adopted at HV automotive applications with wide operation ranges of VIN = 4.5–60 V, VO = 1.2–5 V, and IO up to 1 A for providing the uniformly regulated VO over the chip area. Each linear regulator (LR) in the proposed SDLR consumes low quiescent current of 3.5 μA, while the number of LRs can be efficiently scalable with additional 2.7 μA per LR regardless of IO.