Hyung-Min Lee

Prof. Dr. Hyung-Min Lee

School of Electrical EngineeringKorea University, Seoul, Korea
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 June 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
WJWoojoong Jung
Woojoong Jung
SSSe-Un Shin
Se-Un Shin
SHSung-Wan Hong
Sung-Wan Hong
SYSung-Min Yoo
Sung-Min Yoo
TKTae-Hwang Kong
Tae-Hwang Kong
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
This paper proposes a loop-free auto-calibration technique for self-balancing of flying capacitors in a three-level DC–DC buck converter. The proposed converter utilizes a dual- path power stage with balancing switches that adaptively short flying capacitors at de-energizing phases. Thus, the dual-path three-level converter ensures that flying capacitor voltages are self-balanced at half the input voltage without using additional feedback calibration loops, leading to robust operation and competitive efficiencies. The prototype was fabricated in 0.13-μm CMOS BCD process and adopted two flying capacitors of 4.7 μF each and an inductor of 10 μH with a DC resistance of 128 mA. When an 8 V input was converted to a 3 V output voltage with a load current of 400 mA, the measured efficiency was 88.6% at 800 kHz switching, while flying capacitors are automatically balanced.

18 November 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SSSe-Un Shin
Se-Un Shin
SHSung-Wan Hong
Sung-Wan Hong
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
GCGyu-Hyeong Cho
Gyu-Hyeong Cho
This paper proposes a new boost converter topology called dual-path step-up DC-DC converter (DPUC). Unlike the conventional boost converter (CBC), the DPUC has a hybrid structure using one inductor and one flying capacitor to make dual current delivery paths. This allows continuous current delivering to the output, reducing both the DC level of the inductor current and the output voltage ripple. Therefore, the DPUC has higher efficiency and smaller output voltage ripple than those of CBC. In addition, the feedforward characteristic of the flying capacitor can alleviate the effect of RHP-zero that degrades the transient response. Even with the inductor DCR of 200mΩ, the DPUC achieves a high efficiency of 95.2% and a small ripple of up to 15mV.

7 June 2023 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
HPHyunjun Park
Hyunjun Park
WJWoojoong Jung
Woojoong Jung
MKMinsu Kim
Minsu Kim
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
This article proposes an output capacitor-less NMOS low-dropout regulator (LDO) using wide-range adaptive-gain nested Miller compensation (WAG-NMC) and pre-emphasis inverse (PI) biasing. Due to WAG-NMC, the LDO can provide a wide range of load current ( $I_{\mathrm{LOAD}}$ ) from 0.1 to 300 mA while maintaining sufficiently high phase margin (PM) above 60 $^{\circ}$ at all $I_{\mathrm{LOAD}}$ conditions. WAG-NMC also extends a loop bandwidth (BW) up to 17.5 MHz with using only small compensation capacitors ( $C_{\text{C}}$ ) of 6.3 pF in total. Moreover, PI biasing enhances a slew rate (SR) at the gate of the NMOS power transistor by injecting an adaptive PI current into a supersource follower (SSF), which further improves transient response. The proposed LDO fabricated in a 180-nm CMOS process was fully integrated with an on-chip load capacitor ( $C_{\text{L}})$ of 100 pF. The LDO ensures small undershoot and overshoot of 48 and 59 mV, respectively, against large $\Delta I_{\mathrm{LOAD}}$ of 299 mA due to wide-BW and high SR. The proposed LDO also achieves a best figure of merit (FoM) of 1.72 ps among the state of the arts.

3 December 2018 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
KKKi-Duk Kim
Ki-Duk Kim
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
SHSung-Wan Hong
Sung-Wan Hong
GCGyu-Hyeong Cho
Gyu-Hyeong Cho
A non-inverting buck-boost converter with state- based current control is proposed for Li-ion battery management. Unlike conventional multi-mode control in buck-boost converters, our control scheme utilizes a state controller with a single-level error current and a state checking clock to define the operation mode at every cycle. The state-based buck-boost (S3B) converter enables seamless mode transition and stable output regulation with fixed interleaving patterns even when input and output voltages are similar, ensuring robust mode change with inherent hysteresis. The prototype IC was fabricated in 0.18-μm BCD process and achieved 90.9% efficiency with 1.1-A maximum load current capability at 1-MHz switching frequency.

30 September 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
MKMinjae Kim
Minjae Kim
JAJisan Ahn
Jisan Ahn
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
Wireless power/data transfer (WPDT) through an inductive link has been an essential technique in a wide range of applications, especially for implantable medical devices (IMD), which require high power efficiency for safe operation and high data rate for continuous telemetry. This article proposes an efficient WPDT system with current-modulated energy-reuse back telemetry (ER-BT), which can induce instantaneous changes of load impedance at Rx for BT data rate up to 1 Mb/s, while reusing BT current to supply the load, improving the system power efficiency. The WPDT system also utilizes an energy-adaptive dual-input low-dropout regulator (LDO) to store and optimally reuse the BT energy for IMDs against data rate or load variations. The proposed system was fabricated in a 180-nm 1.8-/5-V standard CMOS process and measured with a coupled-coil inductive link operating at 13.56 MHz to provide a supply voltage of 1.8 V for IMDs. The proposed ER-BT can save the energy up to 42% during the BT operation compared to energy losses of the conventional short-coil (SC) BT when the inductive link provides the input power of 3.05 mW.

12 October 2018 in Electronics
Verified
Journal Article
Open access
PDF file
HYHoyoung Yu
Hoyoung Yu
HLHansol Lee
Hansol Lee
SLSangil Lee
Sangil Lee
YKYoungmin Kim
Youngmin Kim
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
In this paper, we review recent advances in reverse engineering with an emphasis on FPGA devices and experimentally verified advantages and limitations of reverse engineering tools. The paper first introduces essential components for programming Xilinx FPGAs (Xilinx, San Jose, CA, USA), such as Xilinx Design Language (XDL), XDL Report (XDLRC), and bitstream. Then, reverse engineering tools (Debit, BIL, and Bit2ncd), which extract the bitstream from the external memory to the FPGA and utilize it to recover the netlist, are reviewed, and their limitations are discussed. This paper also covers supplementary tools (Rapidsmith) that can adjust the FPGA design flow to support reverse engineering. Finally, reverse engineering projects for non-Xilinx products, such as Lattice FPGAs (Icestorm) and Altera FPGAs (QUIP), are introduced to compare the reverse engineering capabilities by various commercial FPGA products.