Mussakhan A. Aryslan

Mussakhan A. Aryslan

Auto-generated profile, based on publicly available information

Mussakhan A. Aryslan

Department of Physics School of Sciences and Humanities Nazarbayev University Astana Kazakhstan

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2026 in Advanced Photonics Research
Verified
Journal Article
Open access
AMAdilet T. Muratov
Adilet T. Muratov
MAMussakhan A. Aryslan
Mussakhan A. Aryslan
YYYerassyl Yerlanuly
Yerassyl Yerlanuly
ABAlmaz R. Beisenbayev
Almaz R. Beisenbayev
ESErik O. Shalenov
Erik O. Shalenov
Askhat N. JumabekovAskhat N. Jumabekov
Askhat N. Jumabekov
Intense pulsed light (IPL) annealing is a rapid heat treatment technique that significantly reduces the fabrication time of flexible printed perovskite solar cells (FPPSCs) and is compatible with roll‐to‐roll (R2R) systems. This work presents the results of the optimization of IPL annealing for the tin(IV) oxide (SnO 2 ) electron‐transport layer (ETL) and systematically compares IPL‐annealed samples with their hot plate‐annealed counterparts, designated as REF‐SnO 2 . Thin‐film characterization reveals that the optimal condition, referred to as IPL‐SnO 2 , involves a two‐step annealing process: hot plate drying at 100°C for 5 min followed by a single flash with a pulse voltage of 2400 V and a pulse duration of 1000 μs. Notably, IPL‐SnO 2 and REF‐SnO 2 films exhibit nearly identical electrical, optical, and morphological properties. Moreover, devices fabricated with IPL‐SnO 2 and REF‐SnO 2 ETLs demonstrate comparable photovoltaic performance, reaching average power conversion efficiencies (PCEs) of 8.92% and 8.94%, respectively. Photostability tests show that IPL‐SnO 2 devices are operational after 4500 min of continuous illumination. To distinguish the immediate effect of IPL annealing from that of preannealing, characterizations are conducted in parallel on nonannealed and preannealed samples, termed WA‐SnO 2 and PRE‐SnO 2 , respectively. These findings confirm that IPL annealing is a promising approach for scaling up FPPSCs.

30 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
BKBaglan A. Kyrykbay
Baglan A. Kyrykbay
AMAndrii I. Mostovyi
Andrii I. Mostovyi
HPHryhorii P. Parkhomenko
Hryhorii P. Parkhomenko
RZRakhymzhan Ye. Zhumadilov
Rakhymzhan Ye. Zhumadilov
MAMussakhan A. Aryslan
Mussakhan A. Aryslan
Askhat N. JumabekovAskhat N. Jumabekov
Askhat N. Jumabekov
Radiation-resistant photodetectors (PDs) are critically important for space electronics, satellite communication systems, and radiation monitoring devices. However, the operational stability of conventional semiconductor PDs deteriorates under proton irradiation due to radiation-induced defects. Although carbon nanowalls (CNWs) are considered promising radiation-tolerant nanomaterials, the long-term stability of CNW-based PDs under repeated pulsed proton irradiation remains insufficiently studied. In this work, Si/MoOx/CNWs heterojunction PDs were systematically investigated under multiple pulsed proton irradiation cycles at fluences of 1012, 2 × 1012, 5 × 1012, and 1013 p/cm2. The material characteristics and the optoelectronic properties of the fabricated devices were systematically evaluated through various analytical techniques. Before irradiation, the devices exhibited a broadband photoresponse in the 300-1150 nm range, with a maximum external quantum efficiency (EQE) of ~47%, responsivity of ~0.34 A/W, and detectivity of ~8.8 × 1010 Jones. After irradiation, EQE, responsivity, and detectivity gradually decreased with increasing fluence, while dark current and noise level increased. Raman and X-ray photoelectron spectroscope (XPS) analyses revealed irradiation-induced structural disorder and defect-state formation. Nevertheless, the CNWs films preserved their graphitic structure and morphology even after irradiation at 1013 p/cm2. These results demonstrate the potential of Si/MoOx/CNWs PDs for radiation-resistant optoelectronic applications.

3 July 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
MAMussakhan A. Aryslan
Mussakhan A. Aryslan
YNYersain K. Nurmagambetov
Yersain K. Nurmagambetov
DSDinmukhamed Z. Sailau
Dinmukhamed Z. Sailau
AMAdilet T. Muratov
Adilet T. Muratov
HPHryhorii P. Parkhomenko
Hryhorii P. Parkhomenko
Askhat N. JumabekovAskhat N. Jumabekov
Askhat N. Jumabekov
Printed flexible perovskite solar cells (PFPSCs) have attracted growing attention as lightweight and high-specific-power energy sources for next generation terrestrial and space applications. However, scalable manufacturing remains constrained by slow conventional thermal annealing processes that are incompatible with high-throughput roll-to-roll production. In this work, photonic processing was investigated as a rapid alternative to conventional hot-plate treatment for the fabrication of PFPSCs. Perovskite layers processed under non-annealed (NA), hot plate annealed (HP), and optimized intense pulsed light (IPL) annealed (also referred to as photonic processing) conditions were systematically compared in terms of structural, optical, electronic, photovoltaic, photostability, mechanical, and radiation-resistance properties. X-ray diffraction analyses confirmed α-phase formation in all films, while only the HP sample exhibited a PbI2 impurity peak. The optimized IPL film showed enhanced photoluminescence, prolonged charge carrier lifetime, and the highest average device efficiency (~12.0%), outperforming HP (~11.0%) and NA (~6.5%) devices. Electrical characterization revealed reduced trap-assisted recombination and faster internal response in IPL devices. Moreover, IPL devices demonstrated enhanced mechanical and photo-stability, while maintaining radiation tolerance comparable to HP devices after Kr ion irradiation. These results demonstrate that photonic processing is a rapid and effective post-treatment strategy that can be considered as an alternative for conventional thermal annealing while simultaneously highlighting its strong potential for roll-to-roll manufacturing of flexible photovoltaics for Earth and aerospace applications.

17 September 2026 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
MAMussakhan A. Aryslan
Mussakhan A. Aryslan
YNYersain K. Nurmagambetov
Yersain K. Nurmagambetov
DSDinmukhamed Z. Sailau
Dinmukhamed Z. Sailau
AMAdilet T. Muratov
Adilet T. Muratov
HPHryhorii P. Parkhomenko
Hryhorii P. Parkhomenko
Askhat N. JumabekovAskhat N. Jumabekov
Askhat N. Jumabekov

12 August 2026 in Advanced Electronic Materials
Verified
Journal Article
Open access
PDF file
ABAlmaz R. Beisenbayev
Almaz R. Beisenbayev
MAMussakhan A. Aryslan
Mussakhan A. Aryslan
YNYersain K. Nurmagambetov
Yersain K. Nurmagambetov
BIBauyrzhan Idreisov
Bauyrzhan Idreisov
HPHryhorii P. Parkhomenko
Hryhorii P. Parkhomenko
YYYerassyl Yerlanuly
Yerassyl Yerlanuly
Self‐powered perovskite photodiodes are promising candidates for low‐power optical sensing, yet their stability under particle irradiation remains insufficiently understood. In this work, we investigate the influence of 0.5 MeV proton irradiation on fully printed carbon‐electrode perovskite photodetectors. The devices were exposed to irradiation fluences of 10 13 , 10 14 , and 10 15 protons cm −2 and systematically characterized through structural, optical, chemical, and electrical measurements. Structural characterization shows that the main perovskite phase is preserved after irradiation, while weak additional diffraction features and XPS binding‐energy shifts indicate defect formation and modifications in the local Pb–halide coordination environment. Optical measurements reveal photoluminescence quenching and shorter carrier lifetimes, confirming enhanced non‐radiative recombination. Under self‐powered (0 V) operation, a reference device exhibits a photocurrent of 7.8 mA cm −2 under 100 mW cm −2 illumination with a maximum responsivity of 0.31 A W −1 and detectivity on the order of 10 10 Jones. After irradiation at 10 15 protons cm −2 , the photocurrent and responsivity decrease to 3.3 mA cm −2 and 0.19 A W −1 , respectively. Although proton irradiation significantly reduces the photovoltaic and photodetection performance, the photodiodes remain functional and maintain a stable photoresponse, indicating that irradiation primarily increases non‐radiative recombination rather than causing complete loss of device operation.