Welding Research Institute and Engineering Research Center of Advanced Manufacturing Technology for Automotive Components-Ministry of Education, Beijing University of Technology, Beijing 100124, China
Auto-generated profile, based on publicly available information
Zhenyang Lu
Welding Research Institute and Engineering Research Center of Advanced Manufacturing Technology for Automotive Components-Ministry of Education, Beijing University of Technology, Beijing 100124, China
Expulsion identification is of significance for welding quality assessment and control in resistance spot welding. In order to improve the identification accuracy, a novel wavelet decomposition and Back Propagation (BP) neural networks with the peak-to-peak amplitude and the kurtosis index were proposed to identify the expulsion from electrode force sensing signals. The rapid step impulse and resultant damping vibration of electrode force was determined as a robust indication of expulsion, and this feature was extracted from the electrode force waveform by seven-layer wavelet decomposition with Daubechies5 wavelets. Then, the energy distribution proportion of the decomposed detail signals were calculated, and the highest-energy one was selected as the target signal. Two statistical indexes were introduced in this paper to measure the target signal in overall situation and volatility. The bigger the peak-to-peak amplitude is, the more violent the fluctuation is. Moreover, the higher the kurtosis index is, the stronger the impact is, and the lower the dispersion degree of the data is. Experimental analysis showed that neither the peak-to-peak amplitude nor the kurtosis index could accurately judge the expulsion defect individually, because of the early signal fluctuation, likely affected by the work-piece clamping, work-piece clearance, or the oxide film thickness. Therefore, the BP neural networks were introduced to identify the expulsion defects, which is a mature and stable non-linear pattern recognition method. Testing experiments presented good results with the trained networks and improved the evaluable accuracy effectively in the quality assessment of the resistance spot welding.
A process variant of variable polarity plasma arc welding (VPPAW), that is, the pulsed plasma gas VPPAW process, was developed. The pulsed plasma gas was transmitted into the variable polarity plasma arc through a high-frequency solenoid valve to modify the output of the plasma arc. The collection of arc electrical characteristics, arc shapes, and weld formation from VPPAW, double-pulsed VPPAW (DP-VPPAW), and pulsed plasma gas VPPAW (PPG-VPPAW) was carried out to examine if the pulsed plasma gas was able to play a positive role in improving the stability and quality of the VPPAW process. The arc voltage shows that the pulsed plasma gas had a greater influence on the electrode positive polarity voltage. The lower the plasma gas frequency was, the lower the arc voltage fluctuation frequency was and the greater the arc voltage fluctuation amplitude was. From the arc image, it could be observed that the arc core length had a short decrease during the general rising trend after plasma gas was turned on. The arc core width only had a slight change due to the restriction of the torch orifice. Compared with pulsed current wave, the pulsed plasma gas could better enhance the fluidity of the molten pool to reduce porosity during aluminum keyhole welding.
The WAAM (Wire Arc Additive Manufacturing) process is well-respected because of its low cost and high deposition efficiency; nevertheless, the process has the limitations of high heat input and low forming accuracy. Hybrid manufacturing processes employing both additive and subtractive processes can effectively reduce shape error. The predictive modeling of surface roughness in thermally assisted machining is described in this paper on the basis of three important parameters: feed per tooth, spindle speed, and workpiece temperature. The predictive model indicates that temperature has a very significant influence on the surface quality. An experimental study on thermally assisted machining was performed to obtain the variation law of cutting surface quality with temperature in order to determine the optimal process interval of subtractive processes. Through finite element simulation of thermally assisted machining, the influence law of external main cutting force and the internal mean stress of the cutting material were determined.
The present study aims to investigate the effect of microstructure and texture on mechanical properties of resistance spot welding of high strength steel 22MnB5 and 5A06 aluminium alloy as a function of welding parameters. The pseudo-nugget zones (NZs) at the steel side have undergone full recrystallisation with a fine-grained ferrite structure containing a small amount of retained austenite and a high hardness of approximately 500 HV, which is a 35% increase in hardness compared to the base material (BM) with fine lath martensitic structure. The NZs at the Al side contain both a recrystallisation texture and shear texture. Higher tensile shear strength with increasing weld time could be linked to the random texture at the Al side. The highest tensile shear strength was achieved at an intermetallic layer thickness of 4 mm.