1 January 2023 in Journal of Engineering Sciences
The article shows the influence of the technological system of an automated lathe, in particular cam chucks, on the accuracy of machining bearing rings for production conditions. The value of the deformation during machining, i.e., the non-circularity of the ring of a single row tapered roller bearing 32017X in outer diameter, was investigated. For the study, samples were selected that were processed under the same conditions directly in the production unit of PJSC “SKF Ukraine” without interference with the technological process. The use of replaceable floating cams in the chuck design was proposed to increase the accuracy and productivity of machining. Experimental studies have shown that the machined surface’s ovality depends on the chuck cams’ clamping force. The effectiveness of computer processing of statistical data on the accuracy control of engineering products was shown. Implementing machining accuracy control in production using the Minitab computer program was presented. It was proven that the quality of products is formed under the influence of the use of modern computer technologies at all stages of manufacturing and control of parts, which ensures research in a wide range of changes in technological parameters and comparison of individual studies with actual machining conditions on the machine, with the results of a sufficient level of reliability.
1 January 2025 in Journal of Engineering Sciences
The article shows the impact of technological factors, such as cutting modes, to ensure the kinematic accuracy of gears, in particular, the minimum accumulated pitch error. It analyzes the means of controlling gears’ accuracy in manufacturing parts of a given quality. A theoretical study of the impact of the geometry and accuracy of the technological system’s elements and the gear milling process with a worm cutter on the kinematic accuracy of cylindrical gears was carried out. The impact of the technological modes during gear milling on its accuracy indicators was studied experimentally. As a result, the minimum value of the accumulated pitch error of about 20–32 μm was set for cutting modes within a cutting speed of 20–40 m ̸min, feed rate of 0.5–2.5 mm/rev, and cutting depth of 0.5–2.2 mm. The research was performed using the data from the kinematic accuracy of the accumulated pitch error for a wheel obtained during the measurement control. During the research, metrological means and methods of gear wheel control were implemented. A model for the rational selection of technological modes for machining was developed to ensure the required kinematic accuracy of the gear after its milling with a worm cutter due to the error of the accumulated step and to reduce the number of experiments. Overall, the optimal values of the gear wheel’s cutting modes during tooth milling (the cutting speed of 20 m/min, feed rate of 0.5 mm/rev, and cutting depth of 0.5 mm) were set to provide a minimum accumulated pitch error of 23 μm. The built-in model established that the accumulated circular pitch error largely depends on the cutting feed and depth; however, the cutting speed does not affect it significantly.
14 October 2026 in Journal of Engineering Sciences
The study examines the face grinding of outer rings for 32017-X tapered roller bearing made of LH15 steel with a hardness of 55–64 НRC. A scientific and practical approach was proposed to solve the current problem of ensuring the required quality of bearing workpieces. It was established that the disadvantages of traditional grinding methods for such workpieces include difficulty in achieving the required accuracy and physical-mechanical characteristics: non-parallelism of the end faces of 8–12 μm, surface roughness up to 1.25 μm, surface burns, and reduced hardness. It was proposed to use an intermittent grinding tool with pressurized delivery of cutting fluid through the wheel grooves, as a more rational method than the conventional continuous wheel grinding with flood cooling used in production. Experimental results revealed the technological advantages of the proposed machining: end face roughness improved by 0.4–0.6 μm, parallelism by 2–3 μm, and no surface grinding burns were observed. The surface layer hardness after intermittent wheel grinding increased from 60 to 64 HRC. In the study of the surface microprofile formation during intermittent grinding, the roughness of about 0.1–0.6 μm was ensured at the following parameters: workpiece speed of 4.0–6.0 m/min, cutting depth of 0.1–0.3 mm, and cutting speed of 28‒30 m/s. Minimum non-parallelism values for the ring end faces were achieved with an allowance of 0.2–0.3 mm. The proposed face grinding of bearing rings using an intermittent wheel reduced labor intensity and machining costs by a factor of 1.5–2.0 by combining roughing and reducing energy consumption by 35–40 %. Furthermore, it fully ensured the specified quality and accuracy parameters for the bearing ring outer end faces and is effective for machining large-scale surfaces on both universal and automated machine tools.