1 January 2025 in Journal of Engineering Sciences
The article shows the impact of technological factors, such as cutting modes, to ensure the kinematic accuracy of gears, in particular, the minimum accumulated pitch error. It analyzes the means of controlling gears’ accuracy in manufacturing parts of a given quality. A theoretical study of the impact of the geometry and accuracy of the technological system’s elements and the gear milling process with a worm cutter on the kinematic accuracy of cylindrical gears was carried out. The impact of the technological modes during gear milling on its accuracy indicators was studied experimentally. As a result, the minimum value of the accumulated pitch error of about 20–32 μm was set for cutting modes within a cutting speed of 20–40 m ̸min, feed rate of 0.5–2.5 mm/rev, and cutting depth of 0.5–2.2 mm. The research was performed using the data from the kinematic accuracy of the accumulated pitch error for a wheel obtained during the measurement control. During the research, metrological means and methods of gear wheel control were implemented. A model for the rational selection of technological modes for machining was developed to ensure the required kinematic accuracy of the gear after its milling with a worm cutter due to the error of the accumulated step and to reduce the number of experiments. Overall, the optimal values of the gear wheel’s cutting modes during tooth milling (the cutting speed of 20 m/min, feed rate of 0.5 mm/rev, and cutting depth of 0.5 mm) were set to provide a minimum accumulated pitch error of 23 μm. The built-in model established that the accumulated circular pitch error largely depends on the cutting feed and depth; however, the cutting speed does not affect it significantly.
14 October 2026 in Journal of Engineering Sciences
The study examines the face grinding of outer rings for 32017-X tapered roller bearing made of LH15 steel with a hardness of 55–64 НRC. A scientific and practical approach was proposed to solve the current problem of ensuring the required quality of bearing workpieces. It was established that the disadvantages of traditional grinding methods for such workpieces include difficulty in achieving the required accuracy and physical-mechanical characteristics: non-parallelism of the end faces of 8–12 μm, surface roughness up to 1.25 μm, surface burns, and reduced hardness. It was proposed to use an intermittent grinding tool with pressurized delivery of cutting fluid through the wheel grooves, as a more rational method than the conventional continuous wheel grinding with flood cooling used in production. Experimental results revealed the technological advantages of the proposed machining: end face roughness improved by 0.4–0.6 μm, parallelism by 2–3 μm, and no surface grinding burns were observed. The surface layer hardness after intermittent wheel grinding increased from 60 to 64 HRC. In the study of the surface microprofile formation during intermittent grinding, the roughness of about 0.1–0.6 μm was ensured at the following parameters: workpiece speed of 4.0–6.0 m/min, cutting depth of 0.1–0.3 mm, and cutting speed of 28‒30 m/s. Minimum non-parallelism values for the ring end faces were achieved with an allowance of 0.2–0.3 mm. The proposed face grinding of bearing rings using an intermittent wheel reduced labor intensity and machining costs by a factor of 1.5–2.0 by combining roughing and reducing energy consumption by 35–40 %. Furthermore, it fully ensured the specified quality and accuracy parameters for the bearing ring outer end faces and is effective for machining large-scale surfaces on both universal and automated machine tools.
29 November 2025 in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
The paper addresses an axisymmetric thermophysical problem occurring during deep-hole drilling, based on a proposed mathematical model for temperature calculation using the heat source method and the principles of spatial-temporal correspondence and local influence. The dependencies of the thermal process were determined, taking into account the mutual positioning of the cutting tool and the part, the material of the workpiece, the presence of cooling with cutting fluid, cutting conditions, chip removal, and the duration of the drilling operation itself. This is particularly important for deep drilling, where the heat source is continuously displaced. It was established that the calculation of the temperature field in the workpiece depends on the action of a ring-shaped heat source with a uniform heat release intensity distribution. Theoretical analysis showed that the maximum temperature should not exceed 300 °C (without lubricating and cooling fluid) and 180 °C (with lubricating and cooling fluid), respectively. Standard chromel-alumel thermocouples (temperature range −100 °C to +1000 °C) were used for temperature measurement. Deep-hole drilling experiments were performed on parts made of Steel 45 (analogous to C45E and Ck45 according to the EU standard EN 10083-2) with diameters of 10 mm and 20 mm, using special deep-drilling tools. The machining was carried out on a universal lathe model 16K20, modified for deep drilling. The temperature in the tool-workpiece contact zone and the temperature distribution within the workpiece (temperature gradient) were calculated. The adequacy of the proposed mathematical model was confirmed, as the calculated temperature values corresponded well with the experimental data. Keywords: heat source, deep drilling, thermal conductivity, heat source method, principle of spatial-temporal correspondence.
24 May 2023 in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
In the work, the peculiarities of boring of screw workpieces are described. The regularities of the processes of boring screw non-rigid parts have been established. The specifics of the design of the equipment for boring screw non-rigid parts and the expediency and prospects of using screw workpieces are substantiated. It is based on theoretical and experimental studies. A theoretical generalization and a new solution to the scientific and technical problem expressed in the development and creation of technological processes for processing non-rigid screw workpieces, are presented. This will make it possible to ensure the expansion of technological capabilities and the improvement of technical and economic parameters. Calculations were carried out using a package of applied statistical programs for processing and analyzing the results of experimental studies for a PC. According to these results, the dependences of the response surfaces of the optimization parameter and the two-dimensional section of the response surfaces were constructed and analyzed for a visual representation of the results of the experimental studies. The dependences of the change in cutting force on feed and cutting depth were constructed and analyzed. The dependences of the optimization parameter, that is, the dependence of the cutting force on the change of one input factor with a constant value of the other two factors, were also substantiated. After carrying out research using the program «Statistika», a two-dimensional section of the response surface of the dependence of the cutting force on the feed and depth of cut and the response surface of the dependence of the cutting force on the feed and depth of cut were constructed. The obtained experimental broken line was built based on the results of the conducted research. Approximation of it was carried out according to known standard methods, while the amount of deviation (mismatch) was determined by the method of least squares. Key words: cutting process, feed, cutting depth, nature of loads, boring process, statistical analysis, lathe and screw-cutting machine.