Rotten passion fruits, which are highly available in many countries during some periods of the year, can be used to efficiently produce CoFe 2 O 4 material with special structural and electrochemical characteristics for the hydrogen evolution reaction.
Samples of cobalt-doped neodymium orthoferrite compounds, NdCo x Fe 1−x O 3 (0.0 ≤ x ≤ 0.5) were synthesized via glycine auto-combustion between 250 and 300°C and calcined at 500°C for 2 h. X-ray diffraction showed that all compounds had an orthorhombic perovskite structure with space group Pbnm. Increasing cobalt doping gradually reduced the lattice parameters and contracted the unit cell volume. Both X-ray diffraction and scanning electron microscopy showed that the particles were spherical and in the nano-sized range (19–52 nm) with pores between grains. Vibrating sample magnetometry at room temperature indicated that NdFeO 3 has a high coercive field (1950 Oe) and cobalt substitution for iron led to a decrease in the coercive field, saturation and remanent magnetization, which was as a result of decreased magnetic moments in the crystal and reduced canting of the FeO 6 octahedra. The increase in magnetization and coercive fields with increase of Co was connected to the microstructure (bond lengths and angles, defects, pores, grain boundaries) and crystallite size. The compounds NdCo x Fe 1−x O 3 show antiferromagnetism with weak ferromagnetism due to uncompensated non-collinear moments. These compounds could serve as prototypes for tuning the properties of magnetic materials (ferromagnetic and antiferromagnetic) with potential applications in data storage, logic gates, switches and sensors.
There has been a global increase in energy demand, which has necessitated a considerable interest on renewable energy, amongst which are fuel cells. Research efforts in the Solid Oxide Fuel Cells (SOFC) is towards developing electrolyte materials that operate at intermediate temperatures: 500–800 °C which significantly reduce device cost. The purpose of this work is to prepare lanthanum silicate apatite using a low temperature solution synthesis method as electrolyte material in SOFC and enhance the ionic conductivity via Ni doping at the Si site. Nickel doped apatite La10Si6−xNixO27−δ (x = 0; 0.2; 0.4; 0.8) were synthesized from succinate precursors by co-precipitation and calcined at 1000 °C. The oxyapatites were characterized by Fourier Transformed Infrared analysis, X-ray diffraction, microstructural and elemental analyses, and conductivity measurements on the sintered pellets was carried out by the complex impedance spectroscopy. The X-ray diffraction results confirm the presence of apatite phase with hexagonal structure. The conductivity measurements of the samples show that the ionic conductivity increases with increasing Ni2+ content and temperature. The highest conductivity value, 2.07 × 10–2 S cm−1 at 750 °C was observed for La10Si5.2Ni0.8O27−δ electrolyte material which is higher than most values reported in the literature. Therefore, the synthesized nickel doped lanthanum silicate oxyapatites show enhanced conductivity and are suitable candidates as electrolyte for intermediate temperature SOFC.
This worked is aimed at studying the thermodynamic and kinetic adsorption of methyl orange (MO) onto activated carbon (AC) obtained from Neem oil cakes (NOC). The ACs were synthesized by chemical activation of Neem oil cakes with H 3 PO 4 of 2, 5 and 10 percent (respectively labeled AC-2, AC-5, and AC-10) followed by pyrolysis at 450°C for 1 hr. Various characterizations of the synthesized ACs include Fourier Transformed Infrared spectroscopy FTIR, microstructural and elemental analyses (SEM/TEM, EDS), pH PZC , moisture content, and iodine and methylene blue adsorption methods were used to determine the surface area. The ACs were employed to adsorb methyl orange (MO) from a synthetic aqueous solution. The results obtained show that: pH PZC was less than 7, indicating that the three activated carbons have predominantly acidic surface. The adsorbents AC-5 and AC-10 have microporous and mesoporous structures respectively, with respective specific surface area by iodine adsorption (S I2 ) method estimated to be around 688.45 and 689.70 m 2 /g. The adsorption of MO was pH dependent, with an optimal adsorption at pH =2. The EDS results confirm that these adsorbents are primarily composed of carbon. Results from kinetic studies showed that the adsorption process followed a pseudo second order kinetic model. The experimental data from the equilibrium adsorption of MO on the ACs showed the best fit with the Langmuir isotherm, suggesting monolayer adsorption. Maximum adsorption capacity of 232.558 mg.g -1 was obtained for AC-10. These results show that the adsorption of MO is spontaneous and endothermic. Chemisorption is the predominant mechanism for MO removal on AC-2, AC-5, and AC-10.