1 December 2023 in Physics of Fluids
The ignition and flame propagation in an axisymmetric supersonic combustor were investigated. The laser-induced plasma was employed to ignite the supersonic inflow with a speed of Mach 2.5 and a total temperature of 1486 K. A direct-connect axisymmetric model scramjet with a fully transparent glass combustor was built, which enabled the circumferential and axial flame propagation in the cavity-based axisymmetric supersonic combustor to be visualized by the high-speed photography from the endoscopic and external views, respectively. An initial flame kernel is produced by the laser-induced plasma and propagates to the cavity leading edge along the axial direction. The establishment of the cavity shear-layer flame facilitates circumferential flame propagation. The circumferential flame propagation is coupled with the axial propagation, eventually generating a loop-shaped flame with a central-hole. Acceleration of the flame propagation can be observed, especially when the global equivalence ratio is increased. A plausible explanation for the flame propagation in the axisymmetric supersonic combustor was found using URANS numerical simulation. The axisymmetric cavity generates a low-speed loop-shaped recirculation region and thickened cavity shear-layer with an appropriate local equivalence ratio, resulting in the simultaneous axial and circumferential flame propagation. The increased temperature in the cavity and the thickened cavity shear-layer during the flame propagation produce a more intense heat release and mass transfer, leading to faster flame propagation.
1 March 2023 in Physics of Fluids
High-enthalpy gas streams in a real engine or wind tunnel will contain some trace gases; however, this is often ignored in many studies. To investigate transverse fuel-jet mixing and combustion characteristics in a high-enthalpy inflow with trace-gas species, large-eddy simulations based on the HyShot II configuration have been adopted and verified. It was found that a trace amount of atomic oxygen (O) and nitrous oxide has a direct significance on ignition delay times and can, therefore, influence the overall flame distribution. In addition, the results show a greater sensitivity to the levels of O. The complex shock-wave system generated by the transverse jet is found to be a key factor in enhancing mixing and inducing combustion. It not only facilitates vortex generation by increasing the baroclinic term but also provides regions with high pressure and temperature, which accelerate the chemical-reaction rates for radical generation. The initial ignition locations, characterized by HO2 production rates, are mainly located in the low-speed region close to the injector, e.g., in the recirculation region, while OH is mainly formed downstream and accompanied by strong heat release. Based on the analysis of instantaneous contours and statistical results, the overall combustion was found to be in scramjet mode. The partially premixed flame dominates the combustor, where the combustion mainly lies in the flamelet regime, while the diffusion flame dominates the nozzle, where the combustion is spread over the flamelet regime, the broken flamelet regime, and the perfectly stirred reactor regime.
23 September 2020 in International Journal of Computational Fluid Dynamics
This paper develops a new hybrid finite difference scheme which consists of a nonlinear WENOCU4 scheme to maintain the numerical stability near discontinuities and a fourth-order linear central scheme elsewhere to accurately resolve smooth fluctuations and to speed up the computation. The central scheme is constructed in a robust skew-symmetric form which satisfies energy conservation property. A new efficient discontinuity detector is employed to identify the smoothness of the flowfield. As for the one-dimensional scalar equations, the hybrid scheme behaves almost no attenuation associated with propagation error. The quantitative analysis of the shock-capturing error is investigated. The hybrid scheme also exhibits high-resolution spectral property in the wavenumber space. Extensive cases of Euler equations further demonstrate the high-resolution shock-capturing ability of the detector, remarkable vortices-resolving capacity, and superior computational efficiency of the hybrid scheme. The reduced computational cost of the hybrid scheme is about 30−50% with respect to the baseline scheme.
1 January 2024 in Physics of Fluids
The cavity-assisted scramjet has been proven to be the most promising propulsion system for air-breathing hypersonic vehicles. In this paper, numerical simulations of a Mach 8 axisymmetric scramjet combustor are conducted and validated to investigate the effect of the cavity. The results indicate that the combustion state undergoes significant changes as the combustion heat release increases. Detailed analysis reveals that the role of the cavity in flame stabilization and combustion enhancement also changes with combustion heat release. Under weak heat release conditions, the high-speed environment results in reduced combustion efficiency, and the primary role of the cavity is to stabilize the flame. Increasing the cavity size does not yield significant gains but could bring redundant mass. As heat release intensifies, the combustion enhancement effect of the cavity becomes more prominent. The presence of the cavity dramatically improves fuel combustion efficiency. The distribution of supersonic and subsonic combustion modes, as well as that of premixed and diffusion combustion modes, is also affected by cavity size and combustion heat release. In the engineering development of scramjets, it is suggested that the design of the cavity flameholder should involve careful consideration of combustion heat release.
19 October 2022 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
In this paper, the cavity parameters of length-to-depth ratio, aft ramp angle, and nitrogen throttling positions are numerically studied by a Large Eddy Simulation (LES) combined with the Flamelet/Progress Variable (FPV) model, to investigate the inducing factors and formation mechanism of flame flashback. These numerical studies are validated and compared to our previous experiments. It can be observed from both the calculated and experimental flow field that the larger length-to-depth ratio, sharper aft ramp angle, and nitrogen throttling closer to the cavity strengthen the mixing of fuel wake and promote the jet penetration depth. Meanwhile, the separation of the boundary layer downstream of the cavity can be induced by the shear layer, acoustic oscillation, as well as nitrogen throttling. And the above favorable prerequisites enhance the heat release nearby, while the reverse pressure gradient causes the enlargement of the boundary layer separation in turn. Under this positive feedback, thermal choking is formed and drives the reverse propagation of the high-temperature flame. It is concluded that the downstream boundary layer separation induced by the changes of the cavity parameters is a prerequisite for the flame flashback, and the formation of the thermal choking is the main reason for the flame flashback.
1 September 2023 in Physics of Fluids
High-spatiotemporal-resolution diagnostics are important for capturing fine physicochemical structures in supersonic combustion. In this study, a high-speed camera (HSC)/dual-component planar laser-induced fluorescence (PLIF) simultaneous diagnostic technique is developed and applied to an ethylene-fueled scramjet to determine the flame structures and heat release characteristics of cavity shear-layer stabilized combustion. CH2O-PLIF and OH-PLIF simultaneous imaging techniques are used to capture the transient structures in the preheat and product zones of the flame, while the heat release zone (HRZ) is identified by the product of these two signals. Synchronized HSC techniques are used to capture the full-band flame fluorescence. The flame base was found to stabilize in the cavity shear layer at a certain distance downstream of the leading edge. The HRZ was initiated near the flame base and gradually spread into the mainstream. Upstream of the HRZ, the partially premixed fuel jet undergoes preheating oxidation reactions, forming the preheat zone adjacent to the HRZ. Downstream of the HRZ, hot products were produced, forming the product zone distributed in both the cavity and mainstream. The central role of the cavity is to provide a favorable environment for stabilizing the flame base rather than participating in heat release reactions. Schlieren images and wall pressure distributions are also documented, constituting a dataset that could be used to validate computational models.