20 July 2018 in IEEE Transactions on Industrial Informatics
To supporting the systematic requirements of higher spectrum efficiency and user deployment density in future industrial internet-of-things (IIoT), traditional orthogonal multiple access schemes, such as orthogonal frequency division multiplex, are quite limiting. Non-orthogonal multiple access has been recognized as one of enabling technologies for IIoT in 5G network. In this paper, we have proposed an alternative non-orthogonal multiple access scheme called interleave-grid multiple access (IGMA). Depending on interleaving and grid-mapping process, IGMA is capable to provide reliable block error rate performance, marvelous user multiplexing capability, as well as robustness against inter-cell interference. Interleave-grid multiple access can apply various detection and decoding techniques at receiver sides to improve the detection performance with acceptable complexity. Both of link-level and system level results show the promising benefits of interleave-grid multiple access, in particular that nearly seven times user multiplexing gain compared with orthogonal frequency division multiple access has been observed in the system-level simulation. In addition, a hardware test-bed has been implemented to verify the interleave-grid multiple access performance and the testing results proved the strong competitiveness of interleave-grid multiple access over orthogonal frequency division multiple access in terms of block error rate performance in user overloading scenarios.
26 June 2023 in IEEE Journal on Selected Areas in Communications
Full duplex (FD) communication is considered as a promising technology in the development of 5G-advanced and 6G systems as it theoretically doubles the capability of channel. However, this improvement relying on a simultaneously bidirectional manner of communication induces intrinsic self-interference (SI) demanding to be fully cancelled, which is generally intractable. This challenge is minimized in the scenario of integrated access and backhaul (IAB) networks operated in millimeter wave (mmW) band, as its transceivers are stationary and the complexity of SI is greatly reduced by beamforming technique. As a matter of fact, FD can be a pioneering technique to unlock the full potential mmW-based IAB network by releasing its suffering of the half-duplex inefficiency. This article presents the design principle and validation of a practical SI cancellation (SIC) technique in the case of high transmission power class in mmW-based IAB networks. The proposed technique sequentially eliminates SI from the spatial, RF, and digital domains that reduces the SI down to the noise floor. To validate the technique, a prototype system is developed in accordance with 5G IAB specifications and field tests are conducted. Results suggest that the designed mmW SIC transceiver significantly reduces residual-interference to noise ratio (R-INR) to 2.1 dB or less. Additionally, a system-level simulation is conducted in line with 5G IAB evaluation methodology, which explores the potential performance gain of the proposed technique in presence of cross-link interference (CLI). Results indicate that the method could yield a cell throughput gain of about 84%, compared to the current time division duplex deployment.
24 February 2022 in IEEE Transactions on Vehicular Technology
As more and more people choose high-speed rail (HSR) as a means of transportation for short trips, there is ever growing demand of high quality of multimedia services. With its rich spectrum resources, millimeter wave (mm-wave) communications can satisfy the high network capacity requirements for HSR. Also, it is possible for receivers (RXs) to be equipped with antenna arrays in mm-wave communication systems due to its short wavelength. However, as HSRs run with high speed, the received signal power (RSP) varies rapidly over a cell and it is the lowest at the edge of the cell compared to other locations. Consequently, it is necessary to conduct research on RX beamforming for HSR in mm-wave band to improve the quality of the received signal. In this paper, we focus on RX beamforming for a mm-wave train-ground communication system. To improve the RSP, we propose an effective RX beamforming scheme based on deep reinforcement learning (DRL), and develop a deep Q-network (DQN) algorithm to train and determine the optimal RX beam direction with the purpose of maximizing average RSP. Through extensive simulations, we demonstrate that the proposed scheme has better performance than the four baseline schemes in terms of average RSP at most positions on the railway.
1 October 2026 in IEEE Transactions on Vehicular Technology
In modern wireless systems, the process of acquiring channel state information (CSI) has become increasingly critical yet challenging, driven by the conflicting needs of expanding antenna arrays and the pursuit of high spectral efficiency. Recent research particularly leveraging joint source-channel coding and modulation (JSCM) via autoencoder architectures, has demonstrated initial promise in significantly enhancing CSI feedback effectiveness. However, a substantial gap persists between algorithm research and practical realization, particularly concerning real-world validation and systematic design methodologies. This article introduces a comprehensive framework enabling JSCM-based CSI feedback, which encompasses a learning methodology robust against wireless channel imperfection and protocol designs tailored for seamless integration into practical cellular systems. A hardware proof-of-concept (PoC) platform is developed and deployed, where experimental results substantiate the proposed method's superiority in realistic wireless environments. Furthermore, by synergizing technical and protocol innovations, this article resolves three critical challenges impeding the deployment of JSCM-based CSI feedback in future 6G networks: variant resource allocation, low peak-to-average power ratio (PAPR) waveforms design, and accurate channel quality indication (CQI) estimation. Equipped with these enabling techniques, the proposed JSCM-based CSI feedback solution is positioned for 6G adoption, demonstrating substantial throughput improvements over conventional separate source and channel coding (SSCC) implementations.