We have studied the intrinsic doping level and gate hysteresis of graphene-based field effect transistors (FETs) fabricated over Si/SiO(2) substrates. It was found that the high p-doping level of graphene in some as-prepared devices can be reversed by vacuum degassing at room temperature or above depending on the degree of hydrophobicity and/or hydration of the underlying SiO(2) substrate. Charge neutrality point (CNP) hysteresis, consisting of the shift of the charge neutrality point (or Dirac peak) upon reversal of the gate voltage sweep direction, was also greatly reduced upon vacuum degassing. However, another type of hysteresis, consisting of the change in the transconductance upon reversal of the gate voltage sweep direction, persists even after long-term vacuum annealing at 200 °C, when SiO(2) surface-bound water is expected to be desorbed. We propose a mechanism for this transconductance hysteresis that involves water-related defects, formed during the hydration of the near-surface silanol groups in the bulk SiO(2), that can act as electron traps.
We report the synthesis of thermoelectric compounds, Cu3SbSe3 and Cu3SbSe4, employing the conventional fusion method followed by spark plasma sintering. Their thermoelectric properties indicated that despite its higher thermal conductivity, Cu3SbSe4 exhibited a much larger value of thermoelectric figure-of-merit as compared to Cu3SbSe3, which is primarily due to its higher electrical conductivity. The thermoelectric compatibility factor of Cu3SbSe4 was found to be ∼1.2 as compared to 0.2 V−1 for Cu3SbSe3 at 550 K. The results of the mechanical properties of these two compounds indicated that their microhardness and fracture toughness values were far superior to the other competing state-of-the-art thermoelectric materials.
Zinc oxide (ZnO) one-dimensional nanostructures are extensively used in ultra-violet (UV) detection. To improve the optical sensing capability of ZnO, various nickel oxide (NiO) based p–n junctions have been employed. ZnO/NiO heterojunction based sensing has been limited to UV detection and not been extended to the visible region. In the present work, p-NiO/n-ZnO composite nanowire (NW) heterojunction based UV-visible photodetector is fabricated. A porous anodic aluminum oxide template based electrochemical deposition method is adopted for well separated and vertically aligned growth of composite NWs. The photoresponse is studied in an out of plane contact configuration. The fabricated photodetector shows fast response under UV-visible light with a rise and decay time of tens of ms. The wide spectral photoresponse is analyzed in terms of conduction from defect states of ZnO and interfacial defects during p–n junction formation. Light interaction with heterojunction along the length of the composite NW results in enhanced visible photoresponse of the detector and is further supported by simulation.
Zinc oxide (ZnO) based ultraviolet (UV) photodetectors have been fabricated and their photoresponse is studied in Schottky diode configuration. A cost-effective single-step electrochemical deposition method is adopted for the growth of ZnO film with nanorod (NR) and nanoflake morphology. A comparative study of the photodetection parameters based on surface trap states, crystallinity, and strain is done for two different morphology films. Significant photocurrent enhancement is observed for the nanorods under UV light, with appreciable photoresponse in the blue region. A template-assisted growth of ZnO NR film is proposed for better photoresponse and sensitivity of the device, useful for various optoelectronic applications.
The effects of growth rate (Gr), deposition temperature (Td), film thickness (tF), and substrate-induced strain (ϵ) on morphological, crystallographic, and magnetic characteristics of equiatomic CoPt epitaxial films synthesized with pulsed laser deposition are investigated. The (001)-oriented single-crystal substrates of MgO, SrTiO3, and LaAlO3 provide different degrees of epitaxial strain for growth of the disordered face-centered cubic (fcc) and ordered face-centered tetragonal (L10) phases of CoPt. The films deposited at Td≈600 °C on all three substrates are fcc with in-plane magnetization and a narrow hysteresis loop of width ≈200 Oe. The L10 phase, stabilized only at Td≥700 °C, becomes predominantly c-axis oriented as Td is increased to 800 °C. While the crystallographic structure of the films depends solely on the Td, their microstructure and magnetization characteristics are decided by the growth rate. At the higher Gr(≈1 Å/s) the L10 films have a maze-like structure which converts to a continuous film as the tF is increased from 20 to 50 nm. The magnetic coercivity of these films increases as the L10 phase fraction grows with Td and its orientation becomes out of the film plane. The evolution of microstructure with Td is remarkably different at a lower growth rate (≈0.4 Å/s). Here, the structure changes from a self-similar fractal pattern to a disordered assembly of nanodots as the Td is raised from 700 to 800 °C, and is understood in terms of the imbalance between strain and interfacial energies. Magnetic force microscopy of such films reveals no distinct domain walls within the nanoislands, while a clear contrast is seen between the islands of reversed magnetization. Magnetic relaxation measurements on these assemblies of single-domain islands show a negligible decay of magnetization unless a reverse field close to the coercive field (Hc≈30 kOe) is applied. The simple picture of coherent rotation of moment appears incompatible with the time dependence of the remanent magnetization in these films.