20 September 2018 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
A new falling weight test method based on the direct impact on the rail was studied and a backcalculation model was developed to estimate the moduli of the railway substructure layers. The model is three-dimensional, dynamic, and considers the superstructures. After the preliminary studies on the impact system and measurement setup on a test track, a case study was performed on a railway station track. The data were recorded using a series of linear variable differential transformers, geophones, and accelerometers during the proposed falling weight test on the rail. To establish the soil profile and better understanding of the site, geotechnical and geophysical investigation of the soil was done using in situ and conventional laboratory tests. The studies show that the rail falling weight test is feasible and leads to reasonable results. Verification of the backcalculation model with the ABAQUS finite element simulation and comparison of the backcalculated moduli with the results of site investigations show that the function of the backcalculation model is satisfactory.
1 July 2022 in Journal of Transportation Engineering, Part A: Systems
Dynamic load factors ( ) relate the magnitude of vertical wheel-to-rail loads in operation (dynamic loads) to static loads resulting from the weight of the rail car and its contents, as a function of train speed. The equations are often used in the selection of rail steel and cross-sections (weight). Equations for have been put forth by the American Railway Engineering and Maintenance-of-Way Association (AREMA) and others. A limitation of the existing equations is that they have been derived from loads measured at instrumented sections of track and observe the many wheel loads but with constant track conditions. For this study, measurements of dynamic loads from two instrumented wheelset (IWS) as it conducted four passes over a 340 km section of track operated by a North American Class 1 freight railway through the Canadian Prairies. These measurements provided dynamic loads from one loaded freight car over various track structures at differing train speeds. This paper presents the IWS data sets and the variation of dynamic loads between multiple passes of the section of track studied, and the statistical distribution of dynamic loads. New equations are developed for tangent track and nontangent track (inclusive of bridges, grade crossings, curves, and switches).
23 August 2021 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Increasing traffic and speeds on passenger rail lines, and a short season for maintenance work, have motivated the industry to find new methods to assess the condition of existing infrastructure and determine where upgrades are required. In this study, acceleration data from the car body and axle boxes of a revenue car over 92 km of a Canadian passenger rail route in Ontario were collected for two purposes: first, to apply weighted filtering method according to ISO 2631-1997 standard as a technique to determine the locations which highly impact the ride quality and to investigate the effect of type of track features and speed on the ride quality; second, a new analytical method called the envelope of acceleration was applied to use the recorded accelerations to evaluate the alignment and surface roughness along the track. Since the alignment and surface roughness values are always positive and are calculated over a specified length (e.g. 9.5 m, 18.9 m, 38 m) an envelope technique was employed which uses spline interpolations over local maxima of the absolute magnitude of accelerations at every separated n samples corresponding to best fit with track roughness. The regression analysis between the envelope of accelerations and alignment and surface roughness presented a meaningful correlation and showed the applied method is a promising analytical technique to indicate rough sections of the track. The limitations to the application of envelope of acceleration are also discussed.
1 December 2021 in Journal of Transportation Engineering, Part A: Systems
This study develops a new methodology based on computational metrology techniques to measure rail surface roughness from vertical axle-box accelerations. A VIA rail passenger rail car, operating in eastern Ontario, Canada, was instrumented with accelerometers on the car body, trucks, and axle-boxes. The rail surface was measured by a heavy track geometry inspection car. A Gaussian filter was applied to the measured rail surface data and the rail surface roughness was quantified by the root mean square (RMS), as recommended by ISO 11562 for evaluating engineering surfaces. Values of rail surface RMS roughness calculated from axle-box accelerometer data are verified with the measured surface RMS roughness. The overlap ratio and length of the moving window over which the rail surface RMS roughness is calculated are studied with respect to roughness wavelengths, statistical considerations, and maintenance planning purposes. The effect of rail car operating speed as well as the difference between axle-box accelerations measured at two axles of the instrumented rail car on the accuracy of estimating the rail surface RMS roughness are assessed. Filtering techniques and application limitations for calculating roughness are also discussed. The results of this study suggest axle-box acceleration data provide a useful assessment of rail surface roughness for the typical wavelengths between 3 and 25 m and a complementary technique to light and heavy track geometry inspections.