Variability in Eucalyptus wood density and chemical properties is crucial to understanding important factors for the forest-based industry, such as sampling methods and wood suitability as raw material. This study aimed to evaluate the basic density and chemical composition of the radial positions of young wood from the Eucalyptus urophylla clone grown under different precipitation levels. Trees from E. urophylla clonal plantations were collected in Inhambupe, Jandaíra and Itanagra, Bahia State, Brazil. Trees’ basic density and chemical composition (total extractive, lignin, hemicelluloses and α-cellulose) were determined based on the basal log of each tree, at four radial positions (1, 2, 3 and 4). It was found that the basic density and α-cellulose of wood are influenced by the cambial age and the site rainfall. There was greater increase in sections close to the bark (positions 1 and 4) and in more humid environments (sites Itanagra and Jandaríra). This finding highlights the association between wood basic density and chemical composition, mainly in the holocellulose content.
Background: There is a need to find a simpler sampling strategy that still maintains the accuracy of the results. This work aimed to assess different sampling strategies for measuring the basic wood density of Eucalyptus clones along the tree trunk.
Basic wood density is vital for forest-based industries, especially pulp production. However, sample saturation time before analysis poses challenges, with variations in sample types and methods leading to inconsistencies. This study evaluated the impact of different methods, sample types, and saturation parameters on Eucalyptus basic wood density and pulp industry metrics. Five Eucalyptus clones ( E. grandis , E. urophylla , and hybrids) from a São Paulo experimental plot were analyzed. Samples included discs and wood chips collected along the commercial stem. Basic density was determined using the hydrostatic balance method, while chips were also analyzed via the maximum moisture content method. Saturation methods significantly influenced density values, with differences of up to 28 kg/m 3 . Tests 2 and 3 reduced saturation time to 6 days versus 9–15 days for other methods. Density differences between wedges and chips appeared only in clone C2, with variations up to 11 kg m 3 . Saturation methods affected wood consumption predictions, ranging from 2 to 263 m 3 /ton of air-dried pulp. Test 3 (vacuum, pressure, and 100 °C) was the most efficient. Findings highlight that sample type, saturation, and methods influence basic density variability, directly impacting pulp production efficiency.
8 July 2026 in European Journal of Forest Research
This study investigated the influence of contrasting climatic conditions on the proportion and chemical composition of heartwood and sapwood in three young Eucalyptus clones grown under different climatic environments in Brazil. Analyses included extractives content, total lignin, syringyl/guaiacyl (S/G) ratio, ash content, and holocellulose, as well as the determination of heartwood and sapwood proportions along the stem. The results showed that variability was more pronounced between heartwood and sapwood than among growth sites. Heartwood exhibited higher extractives and lignin contents and higher S/G ratios, whereas sapwood showed higher ash content. Extractives and ash were the chemical properties most sensitive to environmental conditions, presenting the highest percentage of variation among sites. Clone C4 showed greater chemical stability across environments. Correlation analysis indicated that only extractives content was positively associated with precipitation and potential evapotranspiration. From a technological perspective, the results demonstrate that more restrictive environments tend to intensify chemical characteristics that hinder pulping performance, highlighting the importance of genotypic selection aimed at chemical stability and the control of industrial variability. Graphical abstract
RESUMO A densidade básica da madeira varia entre espécies e indivíduos, influenciada por fatores como condições ambientais, material genético, manejo silvicultural e idade de corte. O objetivo deste trabalho foi analisar a variabilidade da densidade básica da madeira entre árvores de clones e espécies de Eucalyptus e Corymbia, utilizando dados da literatura e considerando diferentes idades e posições de amostragem ao longo do fuste. Um banco de dados com estudos conduzidos entre 2015 e 2024 sobre a qualidade da madeira dessas espécies foi analisado. A amplitude da densidade básica foi determinada a partir da diferença entre o maior e o menor valor de densidade básica obtido em cada posição amostral entre as árvores de cada material genético avaliado. Os resultados indicaram que a maior variação ocorreu para o gênero Corymbia aos 6 anos (87 Kg m⁻³), seguido por Eucalyptus aos 8 anos (64 Kg m⁻³). Entre as espécies de origem clonal, Eucalyptus saligna apresentou a maior amplitude entre árvores (47 Kg m⁻³), enquanto o híbrido Eucalyptus grandis x Eucalyptus camaldulensis exibiu a menor (19 Kg m⁻³). No que se refere às posições de amostragem ao longo do fuste, as maiores variações ocorreram nas posições correspondentes a 33 e 66% da altura comercial. Para as espécies de Corymbia, a amplitude da densidade básica entre árvores foi maior nas regiões basais, com tendência à homogeneização dos valores a partir da metade do fuste até o topo. Assim, o conhecimento sobre a amplitude da densidade básica entre árvores amostradas é fundamental para aprimorar estratégias de amostragem, permitindo reduzir coletas extensivas e aumentar a representatividade das estimativas da densidade básica ao longo do fuste.