Pramod Kumar Sahoo

Pramod Kumar Sahoo

Auto-generated profile, based on publicly available information

Pramod Kumar Sahoo

Division of Agricultural Engineering, ICAR-Indian Agricultural Research Institute, New Delhi, India

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2013 in Aquaculture
Verified
Journal Article
Closed access
SGS.K. Garnayak
S.K. Garnayak
JMJ. Mohanty
J. Mohanty
TRT.V. Rao
T.V. Rao
SSS.K. Sahoo
S.K. Sahoo
PSP.K. Sahoo
P.K. Sahoo

25 December 2023 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
CPChinmayee Parida
Chinmayee Parida
PSPramod Kumar Sahoo
Pramod Kumar Sahoo
RNRabiya Nasir
Rabiya Nasir
Liaqat Ali WaseemLiaqat Ali Waseem
Liaqat Ali Waseem
Aqil TariqAqil Tariq
Aqil Tariq
WHWesam Hatamleh
Wesam Hatamleh

26 July 2022 in Environment Conservation Journal
Verified
Journal Article
Open access
PDF file
MSMonika Satankar
Monika Satankar
PSPramod Kumar Sahoo
Pramod Kumar Sahoo
IMIndra Mani Mishra
Indra Mani Mishra
ATArun Kumar T.V.
Arun Kumar T.V.
Engineering properties of pearl millet varieties (Pusa composite 443, Pusa composite 701, Pusa1201 and Pusa1801) were evaluated at varying moisture content (10-25% wb). A significant varietal difference was found on studied properties. GMD, Surface area, thousand grain mass, the angle of repose, porosity, internal coefficient of friction, static coefficient of friction (Poly, GI, MS and Al) increased linearly with increase in moisture content within the range of 10 to 25% (w.b.) while the bulk density, true density and hardness decreased linearly with increase in moisture content within the same range. But the value of sphericity showed that direct and indirect relation with moisture content depending variety. The mean value of different cultivars observed and found extreme high and low value of bulk density, true density and porosity for PC701 and Pusa1201, geometric mean diameter and surface area for pusa1801 to Pusa1201, sphericity and internal coefficient of friction for Pusa1201 and PC443, grain mass for Pusa1801 and PC 701, angle of repose for Pusa1201 and PC701, hardness for PC701 and PC443 respectively at moisture ranges from 10 to 25% (wb). 

2 July 2025
Verified
Book Chapter
Closed access
PDF file
RBRupali Balabantaraya
Rupali Balabantaraya
ASAshwin Kumar Sahoo
Ashwin Kumar Sahoo
PSPrabodh Kumar Sahoo
Prabodh Kumar Sahoo
ARAnshu Raj
Anshu Raj

5 February 2026 in WORK: A Journal of Prevention, Assessment & Rehabilitation
Verified
Journal Article
Closed access
SPSajja Poojith
Sajja Poojith
AKAdarsh Kumar
Adarsh Kumar
RKRajeev Kumar
Rajeev Kumar
PSPramod Kumar Sahoo
Pramod Kumar Sahoo
SSSusheel Kumar Sarkar
Susheel Kumar Sarkar
UDUtkarsh Dwivedi
Utkarsh Dwivedi
Background: Lawnmower operators are exposed to high noise and hand-arm vibration (HAV) during their work, which originates mainly from the engine and rotating parts. Higher exposure causes intangible issues for the well-being of the operators, results in immediate and long-term effects on the health, comfort, and safety of the operators. Objective: The study involved measuring noise and HAV from a powered cylindrical lawnmower, developing retrofittable interventions, and evaluating noise and HAV levels with the interventions, and compared their effectiveness using a health risk assessment. Methods: The study was done at three speeds and two modes of operation. The measured noise and HAV amplitudes exceeded the permissible limits of international standards. Higher amplitudes were observed at resonant frequencies of the ear and hand. To mitigate the exposure and increase the safe working hours of the operators, two interventions were developed and retrofitted to the existing lawnmower. The noise and HAV were measured with interventions and compared against pre-intervention phase. Operator's physiological, psychophysical, and postural parameters were also assessed in the lawnmower operation. Results: The developed interventions reduced the noise level from approximately 95 dB(A) to 85 dB(A), satisfying it within internationally permissible limits. HAV has been reduced from 23 ms –2 to below 10 ms –2 , thereby increasing the safe exposure time by approximately 2.3 times with interventions. However, the operator's physiological, psychophysical, and postural parameters remained unchanged as operational requirements remained the same. Conclusion: Noise and HAV reduction through interventions provided a safer working environment for the lawnmower operators.

12 August 2022 in Ecology, Environment and Conservation
Verified
Journal Article
Closed access
NSNishanth M. Stanly
Nishanth M. Stanly
INIndramani
Indramani
RORoafahmadparray
Roafahmadparray
RKRajeev Kumar
Rajeev Kumar
PSPramod Kumar Sahoo
Pramod Kumar Sahoo
SLSatish Devaram Lande
Satish Devaram Lande
A study was undertaken on farmer’s field with an aim to know the pattern of energy utilization duringtillage operation in Indo-Gangectic Plain. A total of 120 farmers were selected from Punjab, Haryana andUttar Pradesh (western UP) based on mechanization level by stratified random sampling technique. Theinformation on different aspects related to tillage machinery ownership, usage, operational conditions andfuel consumption were collected by personal interview. The analysed data revealed that 2-4 ha land sizecould be considered as the threshold level for the farmers to own a tractor in the selected study area.Further, 100 % of the large farmers and 90.91 % medium farmers were found to be tractor owners. On thecontrary, 83.33 % marginal farmers and 80 % of small farmers used tractor on custom hiring basis. Forrotavator the minimum energy consumption was observed with gear of low second. It was observed thatvariations in fuel consumption during tillage operation is mainly attributed to field condition (38%) , correctmatching of tractor and implement system (30%), tillage depth (19%) and skill of operator (9%).