19 November 2019 in IEEE Transactions on Power Electronics
Wireless power transfer systems and plasma generators are among the increasing number of applications that use high-frequency power converters. Increasing switching frequency can reduce the energy storage requirements of the passive elements that can lead to higher power densities or even the elimination of magnetic cores. However, operating at higher frequencies requires faster switching devices in packages with low-parasitics. Wide bandgap (WBG) power devices like Gallium Nitride (GaN) and Silicon Carbide (SiC) devices, have high critical fields and high thermal conductivity that make them good candidates for efficient high-voltage and high-frequency operations. Commercially available GaN and SiC devices have ratings targeting different applications. Lateral GaN devices dominate in lower-voltage (<650 V) and high-frequency applications as they have relatively small device capacitances ( ${C_{oss},C_{iss}}$ ), which make them easy to drive at high frequencies. On the other hand, vertical SiC devices are often used in higher-voltage and lowfrequency applications since they have higher blocking voltages and larger gate charge than their GaN counterparts. As a result, SiC devices usually require high-power and complicated gate drive circuitry. Recent work shows that in both GaN and SiC devices, losses in device ${C_{oss}$ can exceed the conduction losses at high switching frequencies and relatively high voltages under Zero-Voltage-Switching (ZVS) conditions. Moreover, the ${C_{oss}$ energy loss ( ${E_{oss}$ ) per switching cycle increases with frequency in GaN devices but remains roughly independent of frequency in SiC devices. This means that at high frequencies, SiC devices can be preferable due to their smaller ${C_{oss}$ energy loss even when taking into consideration the complexity of the gate drive circuit. In this paper, we present a WBG high-voltage cascode GaN/SiC power device, combining the advantages of both a GaN and a SiC device - namely, simple gate drive requirements, ${E_{oss}$ loss per cycle roughly independent of frequency, and relatively high voltage blocking capability. Comparing this cascode GaN/SiC device with a SiC MOSFET and a SiC JFET of similar voltage ratings and ${R_{ds,ON}$ , we find that the inverter using the cascode GaN/SiC device has the highest efficiency and simplest auxiliary gate drive circuitry. Finally, integrating the cascode GaN/SiC device has the potential benefits of achieving lower ${C_{oss}$ losses, higher device ratings, and better heat removal capability.
2 August 2018 in IEEE Transactions on Power Electronics
This paper presents an impedance compression network (ICN) design in a wireless power transfer (WPT) system to compensate for distance or alignment variations between coils. In mid-range WPT applications, magnetic resonant coupling (MRC) coils are mainly implemented to achieve high efficiency for charging batteries. However, a distance or alignment variation between coils changes their coupling coefficient, and it decreases overall performance of WPT systems because ZVS in a resonant inverter is lost. In order to reduce coil-impedance variation, we propose an ICN that compresses variations in coil impedance. The ICN consists of a resistance compression network (RCN) and phase compression network (PCN) to suppress magnitude and phase variations, respectively, in the coil impedance. Only passive components such as inductors and capacitors are used to implement an ICN.
6 November 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Class 2 ceramic capacitors, such as X7R, have relatively high energy density compared to Class 1 ceramic capacitors. However, they experience changes due to aging, temperature, and electric field. The measured X7R capacitance drop is 1-2% per decade hour due to aging, 18% due to a temperature change from 25°C to 125°C, and 75% due to an applied voltage that is 80% of the rated voltage. The measured equivalent series resistance (ESR) of the X7R capacitors show an increase of 20% to 70% due to aging of 1680 hours, and a 50% fluctuation in value when we apply 20% to 80% of the rated voltage. In switched capacitor (SC) and resonant switched capacitor (ReSC) converters, these variations can shift a converter’s operating point and result in higher equivalent output resistance and lower efficiency.We quantified the converter performance degradation caused by capacitor variations in simulation and demonstrated the results by implementing a 1 MHz 25 W 1:4 Dickson ReSC converter. The converter efficiency decreases from 93.1% to 90.7% as a result of capacitor variations mainly due to aging effect.
11 March 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
In high-frequency (HF) and very-high-frequency (VHF) rectifiers, silicon carbide (SiC) Schottky diodes exhibit higher losses compared to what is reported in manufacturer-provided simulation models, with additional power loss stemming from energy dissipation during the charging and discharging of the junction output capacitance (CJ). Because these losses are not included in manufacturer simulation models and have not been well-studied for commercially available SiC Schottky diodes, we have experimentally measured them using the Sawyer-Tower circuit. From these measurements, we compare the losses across manufacturers, current rating, generation, voltage rating, and packaging. We then demonstrate the performance of these devices on a 20-MHz class-DE rectifier and compare their power dissipation from the simulation and experimental measurements. Finally, by incorporating these losses in device power dissipation calculations in various rectifier topologies, we propose suggestions on device selection to optimize converter efficiencies.
27 January 2022 in IEEE Open Journal of Power Electronics
Class E power amplifiers are widely used in high-frequency applications due to their simplicity and use of only one ground-referenced switch. However, Class E power amplifiers are usually tuned to operate at a fixed frequency due to their resonant nature. Extending the bandwidth of these switch-mode power amplifiers is beneficial in many applications, such as plasma generators and wireless power transfer systems. In this paper, we present a 1 kW wideband Class E power amplifier using Silicon Carbide (SiC) MOSFETs that achieves 93% efficiency at 13.56 MHz with a bandwidth of $\pm$ 1 MHz. We incorporate a reactance compensation network in the output loading stage to achieve wideband operation; design a custom gate drive circuit to reduce the gate power loss and improve thermal performance compared to using a gate driver IC. The total gate power of one SiC MOSFET is measured to be 1.55 W at 13.56 MHz.
8 November 2022 in IEEE Open Journal of Power Electronics
Plasma-assisted nitrogen fixation at atmospheric pressure is a clean and decentralized method for fertilizer production. Among many different plasma discharge types, dielectric barrier discharge (DBD) is one of the few that can generate high output of nitrogen compounds at atmospheric conditions for fertilizer usage. Most DBD generators operate at kHz switching frequencies, however, previous research has found that discharge activities occur at the intervals of the greatest voltage slew rate. The finding implies that operating at higher frequencies can lead to more discharge activities and higher plasma generation. This paper presents a MHz Class E power amplifier with frequency selection to generate DBD plasma at two distinct frequencies. The power amplifier achieves a peak efficiency of 91.5% and outputs 600 W at frequencies of 12.4 MHz and 15.5 MHz.