Zhengzhou University, School of Electrical and Information Engineering, National Center for International Joint Research of Electronic Materials and Systems, International Joint-Laboratory of Electronic Materials and Systems of Henan Province, Zhengz
Auto-generated profile, based on publicly available information
Aoxiang Zhang
Zhengzhou University, School of Electrical and Information Engineering, National Center for International Joint Research of Electronic Materials and Systems, International Joint-Laboratory of Electronic Materials and Systems of Henan Province, Zhengz
The superlattice electron blocking layer (EBL) has been proposed to reduce the electron leakage of the deep ultraviolet light emitting diodes (DUV-LEDs). However, the hole transport is hindered by the barriers of EBL and the improvement of hole injection efficiency still suffers enormous challenges. The superlattice step doped (SLSD) EBL is proposed to improve the hole injection efficiency while enhancing the electron confinement capability. The SLSD EBL enhances the electron confinement capability by multi-reflection effects on the electron wave function. And a built-in electric field towards the active region is generated by superlattice step doping, which facilitates the transport of holes into the multiple quantum wells. The Advaced Physical Model of Semiconductor Devices (APSYS) software is used to simulate the DUV-LEDs with conventional EBL, superlattice EBL, superlattice doped EBL, and SLSD EBL. The results indicate that the SLSD EBL contributes to the increased electron concentration in the multiple quantum wells, the reduced electron leakage in the p-type region, the increased hole injection current, and the increased radiative recombination rate. When the current is 60 mA, the external quantum efficiency of DUV-LED with SLSD EBL is increased to 5.27% and the output power is increased to 13.81 mW. The SLSD EBL provides a valuable reference for solving the problems of serious electron leakage and insufficient hole injection of the DUV-LEDs.
We propose two composition-graded quantum barriers (QBs) to improve the performance of AlGaN-based deep ultraviolet laser diodes (DUV-LDs). The optical and electrical properties of three LDs containing conventional QBs, graded increased QBs, and graded decreased QBs were numerically investigated. It was found that the LDs with graded decreased QBs significantly improved the carrier injection efficiency, raised the carrier concentration in the active region, reduced the carrier leakage, and enhanced the stimulated recombination rate of the LDs. Simulation results showed that, at an 80-mA injection current, the threshold current and threshold voltage were reduced to 29.5 mA and 4.78 V, respectively. The slope efficiency was improved to 2.52 W/A, and the electro-optical conversion efficiency was increased to 52.2%. Compared with the conventional structure of LDs, grading the QBs with decreasing Al-content improved the performance of the LD remarkably, which is essential for the development of DUV-LD.
To improve the carrier injection efficiency and optimize the performance of the AlGaN-based deep ultraviolet laser diodes (DUV-LDs), one-way step-shaped quantum barriers (OWS-QBs), a symmetrical step-shaped electron blocking layer (SS-EBL), and a symmetrical step-shaped hole blocking layer (SS-HBL) are proposed. Crosslight software is used to simulate the DUV-LDs with a traditional structure, with OWS-QBs, and with OWS-QBs, a SS-EBL, and a SS-HBL. The simulation results and physical mechanism analysis indicate that the SS-EBL, SS-HBL, and OWS-QBs contribute to the increased carrier concentration in the quantum wells, the reduced carrier leakage in the nonactive regions, the increased stimulated emission rate, the reduced threshold current and threshold voltage, and the enhanced output power and electro-optical conversion efficiency of DUV-LDs.
Aluminum-rich p-AlGaN electron-blocking layers (p-EBL) usually block the hole injection in the AlGaN-based deep ultraviolet (DUV) light-emitting diode (LED). Meanwhile, the ionization energy of the magnesium receptors in the aluminum-rich p-AlGaN layer is considerably high, and the conductivity is low, leading to a reduction in the hole injection capability. Consequently, AlGaN-based DUV LEDs suffer from a low internal quantum efficiency (IQE). A structure of p-EBL and hole source layer (p-HSL) using AlN composition gradient AlGaN is proposed. The polarization bulk charges are introduced in both p-EBL and p-HSL (the p-type dual polarization) to shield the polarization-induced electric field and increase the hole energy. Although the single-polarized structure of p-EBL or p-HSL can also effectively enhance the performance of the device, calculation results indicate that the performance of the p-type dual-polarized structure can be doubled. This is because optimizing a single p-EBL or p-HSL can only introduce polarization bulk charge in the monolayer but not in all p-type regions. Therefore, in LEDs with shorter wavelengths, to maximize the hole energy, a dual-polarization structure should be adopted for the p-type region. Based on this, a maximum IQE of 55.65% and an efficiency droop of 4.84% are obtained at a wavelength of 237 nm. Findings of this study provide insights to solve the problem of low IQE in high-performance DUV LEDs.
Deep ultraviolet light-emitting diodes (DUV-LEDs) suffer from significant electron leakage and insufficient hole injection, which result in low carrier injection efficiency and poor output power. The superlattice-doped staggered-stepped (SD-SS) electron-blocking layer (EBL) is proposed to reduce electron leakage and improve hole injection. Advanced Physical Model of Semiconductor Devices (APSYS) software is employed to simulate DUV-LEDs with rectangular EBL, stepped EBL, staggered-stepped (SS) EBL, and SD-SS EBL. Based on the traditional stepped EBL, the SS EBL is designed to enhance electron confinement. In the SS EBL, low-concentration doping is applied in regions with high Al composition to alleviate the difficulty of p-type doping, whereas high-concentration doping is used in regions with low Al composition to improve hole generation. This forms a superlattice doping structure, resulting in the formation of SD-SS EBL. Simulation results indicate that the utilization of SD-SS EBL reduces electron leakage in the p-type region, enhances hole injection in the multiple quantum wells, and increases the radiative recombination rate. When the injection current is 60 mA, the proposed structure achieves an external quantum efficiency of 5.05% and an output power of 13.2 mW. In conclusion, the SD-SS EBL contributes to enhancing electron confinement, reducing the difficulty of p-type doping, and increasing hole generation, which provides valuable insights for developing high-efficiency DUV-LEDs.