Kean Wei Leong

Kean Wei Leong

Auto-generated profile, based on publicly available information

Kean Wei Leong

Universiti Malaysia Perlis, Center of Excellence Geopolymer and Green Technology (CEGeoGTech), Perlis, Malaysia

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2022 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
KLK.W. Leong
K.W. Leong
SRShayfull Zamree Abd Rahim
Shayfull Zamree Abd Rahim
Mohd Fathullah GhazliMohd Fathullah Ghazli
Mohd Fathullah Ghazli
Mohd Firdaus OmarMohd Firdaus Omar
Mohd Firdaus Omar
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
Marcin NabiałekMarcin Nabiałek
Marcin Nabiałek
The increasing needs of using aluminum epoxy composite as a replacement to solid metal rapid prototyping has opened to interests in optimizing its machining processes. This paper reported on the success of optimizing the surface roughness of aluminium epoxy composite using milling process along with a new finding on the best combination parameters. Taguchi method was used as the optimization method whereas spindle speed, feed rate, and depth of cut were set as input factors using an L9 Orthogonal Array. Analysis of Variance was used to identify the significant factors influencing the surface roughness. Experiment was conducted in dry condition using a vertical milling machine and the surface roughness after the machining was evaluated. Optimum combination of cutting parameters was identified after the finest surface roughness (response) based on the signal-to-noise ratio calculated. Cutting parameters selected after preliminary testing are cutting speeds of (2000, 3000 and 4000) rpm, feed rate (300, 400 and 500) mm/min, and cutting depth (0.15, 0.20, and 0.25) mm. The result showed that cutting speed had the largest percentage contribution to surface roughness with 69% and the second highest contribution was feed rate with 22% and depth of cut at 9%. The spindle speed was found as the most significant factor influencing the quality of surface roughness. The result is significant particularly in providing important guidelines for industries in selecting the right combination of parameters as well as to be cautious with the most significant factor affecting the milling process of metal epoxy composite.

28 February 2018 in International Review of Mechanical Engineering (IREME)
Verified
Journal Article
Closed access
PDF file
MAMuhamad Effendi Azamudin
Muhamad Effendi Azamudin
MMMuhamad Saifuldin Abdul Manan
Muhamad Saifuldin Abdul Manan
AAAhmad Faizal Annuar
Ahmad Faizal Annuar
MRMuhamad Firdaus Mohd Ratmin
Muhamad Firdaus Mohd Ratmin
KLKean Wei Leong
Kean Wei Leong
There are few methods that are available for arresting cracks in fracture mechanics such as the use of fastening additional material and stop-hole. Another potential method that could be further developed is by using a kerf to be fabricated parallel to a crack. An earlier study about the use of a kerf as a kerf-crack interaction proved that the presence of the kerf would be able to reduce the stress intensity factor of the crack tip. Therefore, this research is exploring the possibility of using kerf as a crack arresting method. This research focuses on the fatigue test of a specimen that contains an edge crack and an edge kerf in a finite plate under fatigue tension loading. Two types of specimens to differentiate between long and short crack were prepared and tested according to the ASTM standard. The kerf on the specimen was fabricated using wire cut electrical discharge machine with a wire diameter of 0.25 mm. The fatigue test results of the crack growth rate versus the stress intensity factor range, (K were compared with the specimen that only contains an edge crack. The presence of the kerf parallel to the edge crack under tension loading, increased the fatigue cycles requiring additional 3000 cycles to grow the crack from 5.6 mm to 8.9 mm. The presence of the kerf also reduced the fatigue crack growth rate at the early stage i.e for (K less than 19 MPa√m. This indicates that the kerf has good potential as crack arresting method. A similar trend can be observed in the case of shorter crack and kerf. However, the effect is lesser than for the case of longer crack and kerf because the generated kerf-crack interaction is lower when shorter crack and kerf are used. A further study would be required to discover its accurate dimension, configuration and limitation as a crack arresting method. Copyright © 2018 Praise Worthy Prize - All rights reserved.