Badrul Munir

Badrul Munir

Auto-generated profile, based on publicly available information

Badrul Munir

Universitas Indonesia

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 July 2021 in Periodica Polytechnica Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
HPHarris Prabowo
Harris Prabowo
BMBadrul Munir
Badrul Munir
YPYudha Pratesa
Yudha Pratesa
JSJohny W. Soedarsono
Johny W. Soedarsono
The scarcity of oil and gas resources made High Pressure and High Temperature (HPHT) reservoir attractive to be developed. The sour service environment gives an additional factor in material selection for HPHT reservoir. Austenitic 28 Cr and super duplex stainless steel 2507 (SS 2507) are proposed to be a potential materials candidate for such conditions. C-ring tests were performed to investigate their corrosion behavior, specifically sulfide stress cracking (SSC) and sulfide stress cracking susceptibility. The C-ring tests were done under 2.55 % H2S (31.48 psia) and 50 % CO2 (617.25 psia). The testing was done in static environment conditions. Regardless of good SSC resistance for both materials, different pitting resistance is seen in both materials. The pitting resistance did not follow the general Pitting Resistance Equivalent Number (PREN), since SS 2507 super duplex (PREN > 40) has more pitting density than 28 Cr austenitic stainless steel (PREN < 40). SS 2507 super duplex pit shape tends to be larger but shallower than 28 Cr austenitic stainless steel. 28 Cr austenitic stainless steel has a smaller pit density, yet deeper and isolated.

1 October 2021 in Journal of the Neurological Sciences
Verified
Journal Article
Closed access
PDF file
SRSri Rianawati
Sri Rianawati
NANurvia Andriani
Nurvia Andriani
BMBadrul Munir
Badrul Munir
NRNeila Raisa
Neila Raisa

30 December 2024 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
EFEni Febriana
Eni Febriana
ANAldo Yansen Tambor Napitupulu
Aldo Yansen Tambor Napitupulu
JSJohny Wahyuadi Soedarsono
Johny Wahyuadi Soedarsono
BMBadrul Munir
Badrul Munir
ESEddy Sumarno Siradj
Eddy Sumarno Siradj
KJKadek Ambara Jaya
Kadek Ambara Jaya
Indonesia is the country with the largest nickel reserves and production levels in the world. Each ton of nickel production can produce eight tons of by-products in the form of ferronickel slag, which continues to increase due to the minimal recycling process of these by-products. This study aimed to determine the impact of changes in acid concentration and solid/liquid ratio on the leaching extraction of magnesium from ferronickel slag and characterize the transformation of ferronickel slag at each stage of the process. The research was conducted using the alkali fusion method and continued with water leaching and acid leaching using Hydrochloric Acid (HCl) as the solvent. The first step in the investigation was milling to get a powder with the particle size ≤127 µm. The sample powder was subsequently mixed with the Na2CO3 additive in a 50:50 (w/w) ratio and roasted for 60 minutes at 1000 °C. The water leaching procedure was then conducted for 60 minutes at 100 °C, a 1:10 (w/v) ratio, and a stirring speed of 400 rpm. The filtrate and residue were then separated using a filtration process. An acid leaching utilizing HCl with concentration variations of 0.5, 1, and 1.5 M, and solid/liquid ratio (s/l) variations of 1:20, 1:30, and 1:40 (w/v) was performed on the residue. The results of acid leaching were then filtrated again. The filtrate was then characterized by ICP-OES testing. Based on the analysis results, it can be stated that the percentage of magnesium extraction increases as the solid/liquid ratio (s/l) increases but decreases with the increase in HCl concentration. The optimum percentage of magnesium extraction is 64.12 %, which was achieved with the leaching conditions of a solid/liquid ratio (s/l) of 1:40 (w/v) and a HCl concentration of 0.5 M

30 April 2024 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
DSDony Soelistiyono
Dony Soelistiyono
JSJohny Wahyuadi Soedarsono
Johny Wahyuadi Soedarsono
BMBadrul Munir
Badrul Munir
MOMichael Oktavianes
Michael Oktavianes
AKAgus Paul Setiawan Kaban
Agus Paul Setiawan Kaban
DIDedy Iskandar
Dedy Iskandar
This work reports the development of inline inspection (ILI) methodology to enhance the pigging activity for the dented pipeline, facilitate the pigging process to prevent Pipeline Inspection Gauge (PIG) from getting stuck and improve the safety passage for buckled pipelines. The recent report unveils the condition of the UNPIGGABLE pipelines, which reduce the inner diameter of pipelines to 257.51 mm, equivalent to 27.58 % of the initial diameter and restricts the pigging activity. In this report, the pull-through test coupled with the collapsibility test was conducted. The success of the test above allows the ILI equipment based on the magnetic flux leakage (MFL) technique to record the internal and external wall loss inwardly and geometric defect on diameter of the pipelines. The prepared artificial dented pipeline was made before it underwent several tests. Based on the pull-through test, the maximum force of 27000 N is more significant than the pipeline operating pressure to enable the MFL tool to pass through the pipelines despite exhibiting the geometry anomaly. Compressing the opposite magnetic yoke of the collapsibility test is critical, showing that the ILI MFL tool reaches its maximum compression of 242 mm. The value is lower than the minimum internal diameter of 257 mm. The ILI results show that the highest metal loss was achieved at 73 % at 15504 m at the bottom of the inspected pipelines. At the same time, the dented area reduces to more than 6 % of the pipelines’ nominal outer diameter and imposes the pipe’s integrity status to red. The distinctive result of the research can be used to model the future unprecedented pigging process when buckles appear in pipelines У цій роботі повідомляється про розробку методології інспекційного контролю (ІК) для підвищення ефективності очищення пом’ятих трубопроводів, полегшення процесу очищення трубороводів, щоб запобігти застряганню контрольного манометра (КМ) і покращити безпечний прохід для трубопроводів зі скручуванням. Нещодавній звіт розкриває стан трубопроводів, що неможливо проінспектувати та які зменшують внутрішній діаметр трубопроводів до 257,51 мм, що еквівалентно 27,58 % від початкового діаметра, і обмежують очищення. У цьому дослідженні було проведено випробування на протягування в поєднанні з випробуванням на згинання. Успіх вищезазначеного випробування дозволяє обладнанню ІК, заснованому на методі витоку магнітного потоку (ВМП), реєструвати втрату внутрішньої та зовнішньої стінки всередині та геометричний дефект діаметра трубопроводів. Підготовлений штучний м’ятий трубопровід був виготовлений перед тим, як пройти кілька випробувань. Виходячи з випробування на протягування, максимальна сила 27000 Н є більшою, ніж робочий тиск трубопроводу, щоб дозволити інструменту ВМП проходити через трубопроводи, незважаючи на демонстрацію аномалії геометрії. Стиснення протилежного магнітного ярма під час випробування на розбірність є критичним, показуючи, що інструмент ІК ВМП досягає максимального стиснення 242 мм. Значення нижче мінімального внутрішнього діаметра 257 мм. Результати ІК показують, що найвища втрата металу була досягнута на рівні 73 % на глибині 15504 м на дні перевірених трубопроводів. Водночас площа вм’ятин зменшується до більш ніж 6 % від номінального зовнішнього діаметра трубопроводів і надає статус цілісності труби червоного рівня. Відмінний результат дослідження може бути використаний для моделювання майбутнього безпрецедентного процесу очищення, коли вигини з’являються в трубопроводах

26 August 2025 in International Journal of Innovative Research and Scientific Studies
Verified
Journal Article
Open access
BMBadrul Munir
Badrul Munir
VRVika Rizkia
Vika Rizkia
Iwan SusantoIwan Susanto
Iwan Susanto
AHAde Utami Hapsari
Ade Utami Hapsari
RPRetna Deca Pravitasari
Retna Deca Pravitasari
The growing need for lightweight aluminum alloys in transportation and aerospace demands advanced surface protection solutions. While electroless Ni-P coating offers excellent corrosion resistance, its performance critically depends on zincating pretreatment - a process whose multi-step optimization remains insufficiently studied. This study investigates the influence of single, double, and triple zincating on the morphology of zincate layers and their subsequent impact on the deposition of electroless Ni-P coatings. AA5052 underwent zincating treatments in 200 g/L NaOH + 10 g/L ZnO solution before electroless Ni-P deposition at 80°C (pH5) in nickel sulfate and sodium hypophosphite. Surface characterization was performed using FE-SEM/EDS, while electrochemical properties were evaluated through EIS in 0.5M H2SO4 solution. Key findings demonstrate that double zincating generates an optimal surface morphology, in form of porous microstructure (average pore size of 0.28μm), that enhances Ni-P nucleation. This morphology yields the highest Ni percentage, and corrosion resistance exhibiting the largest arc radius semicircle. Single zincating produces discontinuous deposits (0.33μm granules), while triple treatment creates over-smoothed surfaces compromising adhesion. The study concludes that the porous Zn layer from double zincating optimizes Ni-P coating adhesion and corrosion protection by providing mechanical anchoring sites, whereas excessive pretreatment diminishes nucleation efficacy.