6 February 2020 in IEEE Transactions on Power Electronics
9 November 2017 in IEEE Transactions on Industry Applications
Monitoring the condition of battery is beneficial in many applications. Internal impedance of the battery can be used to monitor battery health. The power converter for interfacing the battery bank, can be used to measure battery impedance instead of using any dedicated commercial equipment, thus reducing system cost significantly. However, the power converter has some additional requirements in terms of control and power circuit, to be able to measure battery impedance. This work analyzes the power circuit requirements and describes possible methods to meet them. These additional measures are necessary when power level is medium or high. Advantages and disadvantages of each method are discussed. Among the suggested methods, the in-built PLL of FPGA for enhancing PWM resolution and an interleaved PWM converter circuit approach are used to successfully measure battery impedance with a 3 kW converter. Requirements for the measurement circuit are also discussed and a suitable measurement circuit is proposed.
27 April 2021 in IEEE Transactions on Industry Applications
A selection switch based cell-to-cell voltage equalizer requires only one dual-port dc-dc converter shared by all the cells. A cell-to-cell voltage equalizer is proposed that utilizes a capacitively level-shifted Cuk converter and low-frequency cell selection switches. The absence of isolation transformer and diodes in the equalizer leads to high efficiency, and the use of low-frequency selection switches significantly reduces the cost of the drive circuits. A low-frequency cell selection network is proposed using bipolar voltage buses, where the switch count is almost half, compared to the existing low-frequency cell-to-cell equalizers for the case of a large number of cells. A novel approach for cell voltage recovery compensation is proposed, which reduces the number of operations of the selection switches and the equalization time. The proposed equalizer is implemented with relays and verified with an eight-cell Li-ion stack. The developed prototype shows the efficiency of over 90% and good voltage balancing performance during charging, discharging, and varying load conditions. Experimental results also show about one order of magnitude reduction in the number of relay switchings and a significant reduction in equalization time using the proposed voltage compensation.
9 July 2024 in IEEE Transactions on Power Electronics
Solid-state circuit breaker (SSCB) with high efficiency and high gravimetric power density is required for electrified aircraft propulsion (EAP). A cryogenically cooled gallium nitride (GaN) device-based SSCB module is developed for the EAP system to achieve a higher power density than existing SSCBs. The SSCB module is suitable for medium voltage direct current (MVdc) applications and is designed with low-weight modular cold plates. Each module is rated for 750 V, 100 A, and can interrupt a fault current of 1 kA at cryogenic temperature. The SSCB module structure design, thermal interface design, modular cold plate design, and insulation design are discussed. The developed SSCB module prototype achieves a power density of 329 kW/kg and an efficiency of 99.93%. Experimental results of interrupting a fault of 1 kA and insulation test of the SSCB module are provided to validate its operation.
17 August 2022 in IEEE Transactions on Power Electronics
The current limiting function enables the solid-state circuit breaker (SSCB) to have proper protection coordination. It allows sustained overcurrent for a certain period while preventing the fast fault current increase in dc systems. For the conventional method of using switches alone to limit the current, the high loss results in a short withstand time and low current limiting capability of the SSCBs. In this letter, a control strategy is proposed to utilize the energy absorption component to handle the major part of the energy during the current limiting stage to increase the current limiting capability for series-connected SSCB switching cells. The proposed method is experimentally verified to have more than 3X current limiting withstand time compared to the conventional control strategy in a case study.
6 June 2024 in IEEE Transactions on Industrial Electronics
A modular voltage equalizer can be used in a wide variety of applications without changing the module design. However, the modularization of an equalizer topology often involves slow intermodule equalization, additional energy loss, and cost. A study on available modularization techniques shows that transformer-based equalizers offer simple and low-cost modularization methods. Conversely, the transformer-less equalizers can offer a more compact design, but their modularization methods suffer from either high complexity and loss, or slow intermodule equalization speed. In this work, one twowinding transformer is introduced into a transformer-less equalizer module to leverage the modularization benefits of transformer isolation while still achieving a more compact design than transformer-based equalizers. The proposed direct modularization method achieves fast intermodule equalization and fixed design for a variety of applications with a small increase in cost and size. The proposed method is implemented on a transformer-less equalizer and its effectiveness is validated experimentally with a threemodule prototype.