20 November 2019 in Advanced Engineering Materials
Laser lift‐off (LLO) is commonly applied to separate functional thin films from the underlying substrate, in particular light‐emitting diodes (LEDs) on a gallium nitride (GaN) basis from sapphire. By transferring the LED layer stack to foreign carriers with tailored characteristics, for example, highly reflective surfaces, the performance of optoelectronic devices can be drastically improved. Conventionally, LLO is conducted with UV laser pulses in the nanosecond regime. When directed to the sapphire side of the wafer, absorption of the pulses in the first GaN layers at the sapphire/GaN interface leads to detachment. In this work, a novel approach towards LLO based on femtosecond pulses at 520 nm wavelength is demonstrated for the first time. Despite relying on two‐photon absorption with sub‐bandgap excitation, the ultrashort pulse widths may reduce structural damage in comparison to conventional LLO. Based on a detailed study of the laser impact as a function of process parameters, a two‐step process scheme is developed to create freestanding InGaN/GaN LED chips with up to 1.2 mm edge length and ≈5 μm thickness. The detached chips are assessed by scanning electron microscopy and cathodoluminescence, revealing similar emission properties before and after LLO.
15 May 2002 in Macromolecular Symposia
15 December 2022 in Optics Express
The laser-induced ablation threshold of c-plane GaN films upon exposure to ultrashort laser pulses was investigated for different wavelengths from the IR to the UV range and pulse widths between 0.34 and 10 ps. The one-pulse ablation threshold ranges between 0.15 and 3 J/cm2 and shows an increase with the wavelength and the pulse width, except for deep UV pulses. Based on a rate equation model, we attribute this behavior to the efficiency of seed carrier generation by interband absorption. In addition, the multi-pulse ablation threshold was analyzed. Accumulation effects are more prominent in case of IR than with UV pulses and are closely linked to damage precursors. By a thorough structural investigation, we demonstrate that threading dislocations, especially those with a screw component, significantly contribute to laser damage, since they provide a variety of dispersed states within the band gap.
20 August 2021 in IEEE Photonics Journal
MicroLED arrays with the capability of switching each pixel separately with high frequency can serve as structured micro-illumination light engines for applications in sensing, optogenetics, microscopy and many others. We describe a scalable chip process chain for the fabrication of passive-matrix microLED arrays, which were integrated with PCB-based driving electronics. The arrays were produced by deep-etching of conventional planar LED structures on sapphire, followed by filling and planarization steps. The pixel resolution lies in the range of 254 to 2540 pixels-per-inch (ppi), the arrays consist of 32 x 32 pixels. Optical output powers up to 50 µW per pixel were measured. In comparison to CMOS-based approaches, the presented technology is a simplified strategy to produce microLED arrays with high pixel counts.
27 September 2023 in Applied Optics
The design study of a micro illumination tool based on GaN microLED arrays is presented. The high spatio-temporal resolution and the capability of generating fully customized optical patterns that characterize the proposed platform would enable the manipulation of biological systems, e.g., for optogenetics applications. Based on ray tracing simulations, the design aspects that mainly affect the device performance have been identified, and the related structural parameters have been optimized to improve the extraction efficiency and the spatial resolution of the resulting light patterns. Assuming that the device is a bottom emitter, and the light is extracted from the n-side, the presence of mesa-structures on the p-side of the GaN layer can affect both the efficiency and the resolution, being optimized for different values of the mesa-side inclination angle. The full width at half maximum (FWHM) of the extracted spots is mainly determined by the substrate thickness, and the relation between the FWHM and the array pitch represents a criterion to define the resolution. Namely, when FWHM<pitch, the spots are assumed to be resolved, while, when FWHM=pitch, a homogeneous distribution of light intensity is observed. The best performance is obtained when an in-GaN micro-lens array is included in the simulated structure, assuming that the substrate has been removed. The spatial resolution of the generated light pattern results as fully preserved, while the extraction efficiency in the best case is up to three times larger than that of a planar GaN/air interface.