Single-phase body-centered cubic (bcc) refractory medium- or high-entropy alloys can retain compressive strength at elevated temperatures but suffer from extremely low tensile ductility and fracture toughness. We examined the strength and fracture toughness of a bcc refractory alloy, NbTaTiHf, from 77 to 1473 kelvin. This alloy’s behavior differed from that of comparable systems by having fracture toughness over 253 MPa·m 1/2 , which we attribute to a dynamic competition between screw and edge dislocations in controlling the plasticity at a crack tip. Whereas the glide and intersection of screw and mixed dislocations promotes strain hardening controlling uniform deformation, the coordinated slip of edge dislocations with {110} and {112} glide planes prolongs nonuniform strain through formation of kink bands. These bands suppress strain hardening by reorienting microscale bands of the crystal along directions of higher resolved shear stress and continually nucleate to accommodate localized strain and distribute damage away from a crack tip.
Although recycling secondary aluminum can lead to energy consumption reduction compared to primary aluminum manufacturing, products produced by traditional melt-based recycling processes are inherently limited in terms of alloy composition and microstructure, and thus final properties. To overcome the constraints associated with melting, we have developed a solid-phase recycling and simultaneous alloying method. This innovative process enables the alloying of 6063 aluminum scrap with copper, zinc, and magnesium to form a nanocluster-strengthened high-performance aluminum alloy with a composition and properties akin to 7075 aluminum alloy. The unique nanostructure with a high density of Guinier-Preston zones and uniformly precipitated nanoscale η‘/Mg(CuZn)2 strengthening phases enhances both yield and ultimate tensile strength by >200%. By delivering high-performance products from scrap that are not just recycled but upcycled, this scalable manufacturing approach provides a model for metal reuse, with the option for on-demand upcycling of a variety of metallic materials from scrap sources.
Magnetic materials with high negative spin polarization have been sought as a building block to increase the design freedom and performance of spintronics devices. In this paper, we investigate negative spin polarization of Mn2VGa Heusler alloy in current-perpendicular-to-plane giant magnetoresistance (CPP-GMR) devices. We fabricated an epitaxial CPP-GMR stack consisting of Mn2VGa/Ag/CoFe with L21 ordering in the Mn2VGa layer and observed negative magnetoresistance (MR), which provided evidence of negative spin polarization. The MR ratio depended on thermal treatments (deposition at an elevated temperature and post-annealing), because these processes affected the ordering, roughness, and magnetic properties of Mn2VGa. The maximum MR ratio reached −1.8% at room temperature and −3.0% at low temperatures, representing the highest among the negative MR values in pseudo-spin-valve CPP-GMR devices despite the underestimation due to an incomplete antiparallel magnetization configuration. These findings demonstrate the potential of Mn2VGa for a material with high negative spin polarization.
The anisotropic magnetoresistance (AMR) effect is one of the fundamental spin-dependent transport phenomena in ferromagnets and has been the subject of numerous experimental observations. However, the origin of AMR including the sign change of the magnetoresistance has not been fully clarified theoretically. In this paper, we observe a large negative AMR ratio in single-crystal thin films upon Ir addition and elucidate its origin by a theoretical model. composition-spread thin films with up to 11% are fabricated on MgO(100) substrates by combinatorial sputtering technique. From x-ray diffraction results, the metastable -ordered phase of is detected from , which does not appear in the bulk equilibrium phase diagram. The ordering is also confirmed by scanning transmission electron microscopy. The AMR ratio of the pure shows a small positive value of 0.3%. In contrast, once the Ir atoms are added, the AMR ratio becomes negative, and it exhibits the largest negative values of −4.7% at 10 K and −3.6% at 300 K for . Using a theoretical model, the sign change of the AMR ratio from positive to negative upon ordering is obtained for high-Ir concentration, which agrees with the experimental results. Thus, the metastable ordering would be the key to observing the negative AMR. These findings provide deep insight into the origin of AMR in heavy-metal-doped ferromagnetic ordered alloys.
22 September 2026 in International Journal of Plasticity