14 May 2014 in Beilstein Journal of Nanotechnology
Over the last decade, significant effort has been put into mimicking the ability of the gecko lizard to strongly and reversibly cling to surfaces, by using synthetic structures. Among these structures, mushroom-like elastomer fiber arrays have demonstrated promising performance on smooth surfaces matching the adhesive strengths obtained with the natural gecko foot-pads. It is possible to improve the already impressive adhesive performance of mushroom-like fibers provided that the underlying adhesion mechanism is understood. Here, the adhesion mechanism of bio-inspired mushroom-like fibers is investigated by implementing the Dugdale–Barenblatt cohesive zone model into finite elements simulations. It is found that the magnitude of pull-off stress depends on the edge angle θ and the ratio of the tip radius to the stalk radius β of the mushroom-like fiber. Pull-off stress is also found to depend on a dimensionless parameter χ, the ratio of the fiber radius to a length-scale related to the dominance of adhesive stress. As an estimate, the optimal parameters are found to be β = 1.1 and θ = 45°. Further, the location of crack initiation is found to depend on χ for given β and θ. An analytical model for pull-off stress, which depends on the location of crack initiation as well as on θ and β, is proposed and found to agree with the simulation results. Results obtained in this work provide a geometrical guideline for designing robust bio-inspired dry fibrillar adhesives.
7 June 2017 in Royal Society Open Science
Synthetic fibrillar adhesives inspired by nature, most commonly by the gecko lizard, have been shown to strongly and repeatedly attach to smooth surfaces. These adhesives, mostly of monolithic construction, perform on par with their natural analogues on smooth surfaces but exhibit far inferior adhesive performance on rough surfaces. In this paper, we report on the adhesive performance of functionally graded microfibrillar adhesives based on a microfibre with a divergent end and a thin soft distal layer on rough surfaces. Monolithic and functionally graded fibre arrays were fabricated from polyurethanes and their adhesive performance on surfaces of varying roughness were quantified from force–distance data obtained using a custom adhesion measurement system. Average pull-off stress declined significantly with increasing roughness for the monolithic fibre array, dropping from 77 kPa on the smoothest (54 nm RMS roughness) to 19 kPa on the roughest (408 nm RMS roughness) testing surface. In comparison, pull-off stresses of 81 kPa and 63 kPa were obtained on the same respective smooth and rough surfaces with a functionally graded fibre array, which represents a more than threefold increase in adhesion to the roughest adhering surface. These results show that functionally graded fibrillar adhesives perform similar on all the testing surfaces unlike monolithic arrays and show potential as repeatable and reusable rough surface adhesives.
22 July 2020 in Bioinspiration & Biomimetics
Most natural fibrillar adhesive structures feature spatula-shaped caps as a common adhesive element. The spatula-shaped tips endow adhesive fiber arrays with on demand adhesion, allowing them to maximize adhesion in a given direction and facilitate effortless detachment. Replication of off-center spatula ends synthetically, a key contributor to directional adhesion, remains a fabrication challenge. In this work, a method to feature synthetic microfiber adhesives with off-center caps is proposed. This new method decouples the shape and placement dependency between the cap and the stem, providing endless possibilities in positioning of the tip with respect to the stem and the two-dimensional shape and the material of both the cap and the stem. Experiments of directional adhesion were carried out to demonstrate switchable adhesion relevant for pick & place type applications, and the ability to generate high friction and easy removal. Fibers with off-center caps were shown to promote easy detachment after strong adhesion in both straight and bent stalks. Straight fibers with off-center caps showed 3-to-5-fold reduction in adhesion when pulled diagonally instead of vertically from the adhering surface. Bent fibers on the other hand provided up to 3 times more maximum shear than adhesion, when fibers are dragged laterally against the cap overhang. These results show the versatility and the potential of the proposed fabrication method in designing application specific directional and switchable adhesives.
19 November 2018 in Beilstein Journal of Nanotechnology
Many organisms rely on densely packed, tilted and curved fibers of various dimensions to attach to surfaces. While the high elastic modulus of these fibers enables an extremely large number of fibers per unit area, where each fiber stands freely without sticking to its neighbors, the tilt/curvature provides them with the compliance and the directional adhesion properties to attach strongly and efficiently to a surface. Recent studies have revealed that many of such organisms also feature materials with a graded elastic modulus that is tailored towards improving the contact area without sacrificing the fiber density. In particular, for male ladybird beetles, research has shown that the adhesive setae feature a material gradient such that the elastic modulus of the material at the junction between the stalk and the divergent distal end is close to minimum. This soft material acts like a flexible joint, improving the bending compliance of the tip. Here, we mimic this feature using tilted, mushroom-like, stiff fibers comprised of a stiff stalk of elastic modulus 126 MPa, a softer tip of elastic modulus 8.89 MPa, and a joint-like element of elastic modulus 0.45 MPa (very soft), 8.89 MPa (soft), or 126 MPa (stiff) in between. The results from load–drag–pull (LDP) experiments performed along (gripping) and against (releasing) the tilt direction indicate that the soft and the very soft joint fibers performed superior to the stiff joint fibers and maintained directionally dependent performance. The soft joint fibers achieved up to 22 kPa in shear and 110 kPa in pull-off stress in the gripping direction, which are twice and ten times higher than that in the releasing direction, respectively. A model to optimize the elastic modulus of the joint-like elements to enable sliding without peeling of the tips has been proposed.
26 January 2023 in IEEE Sensors Journal
The phenomenon through which vibrations are produced with frequencies related the period of fingerprint ridges and the speed they slide across a surface is known as the fingerprint effect. Here, we use a simple bioinspired sensor with parallel, straight, fingerprint-like ridges and a single ferroelectric ceramic transducer to show that the fingerprint effect is orientation dependent and that, if the orientation is known, it can be used to estimate slip speed. Our results, obtained at sliding speeds of 15 mm/s, 20 mm/s, and 25 mm/s and orientations from 0° - 90°, clearly demonstrate this dependence. We then describe a simple algorithm for estimating slip speed in real-time. Using experimental results as input, we use that algorithm to run simulations, using MATLAB software, of real-time slip speed estimation. From these simulations we identify some trade-offs in parameter selection for the slip speed estimation algorithm. Finally, the fingerprint effect is used for real-time slip speed estimation for feedback in a controlled slip experiment.
2 September 2019 in Journal of Turbulence
HEHumberto Bocanegra Evans
+2
Adverse-pressure-gradient turbulent boundary layer flow was inspected at Reynolds number based on momentum thickness, , using particle image velocimetry in a refractive-index-matching flume. Proper orthogonal decomposition was used to quantify the effect of large-scale motions on the Reynolds stresses at the onset of separation and within the separated flow. Results show that approximately of the Reynolds shear stress, , is due to large-scale motions containing of the turbulence kinetic energy at the tested Reynolds number. The decomposed velocity field revealed that only the first of the modes is sufficient to recover of the turbulence kinetic energy. In this partition, the large-scale motion contribution to the streamwise component of the Reynolds normal stress, , is about and continues to grow with flow separation. In addition, the large- and small-scale motions equally contributed to the vertical component of the Reynolds normal stress, , and the contribution of the large-scale motions increased as the flow separated. Overall, results emphasise the significant impact of the large-scale motions on the Reynolds stresses in the separated flow, which may impact flow control strategies.