Yuki Toji

Yuki Toji

Auto-generated profile, based on publicly available information

Yuki Toji

Steel Research Laboratory, JFE Steel Corporation

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2018 in Acta Materialia
Verified
Journal Article
Closed access
XZXianguang Zhang
Xianguang Zhang
GMGoro Miyamoto
Goro Miyamoto
TKTakeshi Kaneshita
Takeshi Kaneshita
YYYasuki Yoshida
Yasuki Yoshida
YTYuki Toji
Yuki Toji
TFTadashi Furuhara
Tadashi Furuhara

1 September 2016 in Acta Materialia
Verified
Journal Article
Closed access
YTYuki Toji
Yuki Toji
HMHiroshi Matsuda
Hiroshi Matsuda
DRDierk Raabe
Dierk Raabe

15 April 2023 in ISIJ International
Verified
Journal Article
Open access
PDF file
YTYuki Toji
Yuki Toji
TNTatsuya Nakagaito
Tatsuya Nakagaito
HMHiroshi Matsuda
Hiroshi Matsuda
KHKohei Hasegawa
Kohei Hasegawa
SKShinjiro Kaneko
Shinjiro Kaneko
The microstructure and mechanical properties of a low-carbon steel produced via the quenching & partitioning (Q&P) heat treatment was investigated, with particular focus on the hole expansion ratio, which is an index of the stretch-flange-formability. 0.19mass%C-1.5mass%Si-2.9mass%Mn steel was annealed at 850 ˚C, then cooled to 150~400 ˚C (QT: quench temperature), followed by holding at 400˚C for 1100 s. Yield strength and hole expansion ratio drastically increased when the QT was below the Ms (martensite start) temperature. The steel with QT of 300 ˚C exhibited not only a higher elongation, which has been well documented, but also a higher hole expansion ratio, when compared to the conventional TRIP steel with QT of 400 ˚C having equal tensile strength around 1200 MPa. The micro-void formation during deformation was suppressed in the steel with QT of 300 ˚C due to the smaller volume fraction of large blocky martensite compared to the TRIP steel. These excellent mechanical properties are attributed to its unique microstructure consisting of a certain amount of tempered martensite, lath-shaped retained austenite and bainitic ferrite, which was generated via the Q&P heat treatment.

24 February 2019 in Metals
Verified
Journal Article
Open access
PDF file
XZXianguang Zhang
Xianguang Zhang
GMGoro Miyamoto
Goro Miyamoto
YTYuki Toji
Yuki Toji
TFTadashi Furuhara
Tadashi Furuhara
The effects of heating rate on the formation of acicular and globular austenite during reversion from martensite in Fe–2Mn–1.5Si–0.3C alloy have been investigated. It was found that a low heating rate enhanced the formation of acicular austenite, while a high heating rate favored the formation of globular austenite. The growth of acicular γ was accompanied by the partitioning of Mn and Si, while the growth of globular γ was partitionless. DICTRA simulation revealed that there was a transition in growth mode from partitioning to partitionless for the globular austenite with an increase in temperature at high heating rate. High heating rates promoted a reversion that occurred at high temperatures, which made the partitionless growth of globular austenite occur more easily. On the other hand, the severer Mn enrichment into austenite at low heating rate caused Mn depletion in the martensite matrix, which decelerated the reversion kinetics in the later stage and suppressed the formation of globular austenite.

1 January 2019 in Tetsu-to-Hagane
Verified
Journal Article
Open access
PDF file
NTNoriyuki Tsuchida
Noriyuki Tsuchida
TTTakaaki Tanaka
Takaaki Tanaka
YTYuki Toji
Yuki Toji
The better uniform elongation of the 1 GPa-grade TRIP-aided multi-phase steel with retained austenite (γR) shape of needle-like was discussed by in situ neutron diffraction experiments during tensile test. The better uniform elongation can be ascribed by not only the deformation-induced martensitic transformation of γR but also the deformation behavior of γR and ferrite phase. Especially, the tensile deformation behavior of γR is found to be closely associated with both of the stress-strain curve and the deformation-induced martensitic transformation of γR. The tensile deformation behavior of γR should be considered as one of the conditions to obtain better TRIP effect.

28 July 2023
Verified
Book Chapter
Closed access
PDF file
THTomoaki Hyodo
Tomoaki Hyodo
TMToshio Murakami
Toshio Murakami
KKKaori Kawano
Kaori Kawano
YTYuki Toji
Yuki Toji
THTakao Horiya
Takao Horiya
TITakashi Ishikawa
Takashi Ishikawa