This study presents a fully coupled thermo-hydro-mechanical (THM) constitutive model for clay rocks. The model is formulated within the elastic-viscoplasticity framework, which considers nonlinearity and softening after peak strength, anisotropy of stiffness and strength, as well as permeability variation due to damage. In addition, the mechanical properties are coupled with thermal phenomena and accumulated plastic strains. The adopted nonlocal and viscoplastic approaches enhance numerical efficiency and provide the possibility to simulate localization phenomena. The model is validated against experimental data from laboratory tests conducted on Callovo-Oxfordian (COx) claystone samples that are initially unsaturated and under suction. The tests include a thermal phase where the COx specimens are subjected to different temperature increases. A good agreement with experimental data is obtained. In addition, parametric analyses are carried out to investigate the influence of the hydraulic boundary conditions (B.C.) and post-failure behavior models on the THM behavior evolution. It is shown that different drainage conditions affect the thermally induced pore pressures that, in turn, influence the onset of softening. The constitutive model presented constitutes a promising approach for simulating the most important features of the THM behavior of clay rocks. It is a tool with a high potential for application to several relevant case studies, such as thermal fracturing analysis of nuclear waste disposal systems.
29 January 2014 in Journal of Geophysical Research: Solid Earth
Chemomechanical processes involved in the deep burial diagenesis of carbonate petroleum reservoirs are still poorly understood. To better understand these processes and explain how porosity and permeability can be preserved at the great depth of DBRs (deeply buried reservoirs), we developed an experimental device allowing both the simulation of high-pressure/stresses/temperature conditions (80°C, 60 MPa of confining pressure, and differential stress up to 40 MPa) of DBR and the circulation of different fluids in rock samples. We tested (triaxial multistep creep tests) four core samples of a cemented limestone and analyzed creep deformations, fluids chemistry, and petrographical and petrophysical properties of samples. Different flow conditions (no flow and flow through) and chemical compositions (natural meteoric water with and without phosphate ions) were considered. Our study showed that the precipitation of calcite on free pore walls of micrites blocks the microporosity between micrite crystals, thus rendering the microporosity inaccessible to fluids. Hence, the connected porosity decreased strongly after experimentation. This is due to the PSC (pressure solution creep) which is the main process implied in the porosity reduction of a carbonate rock during deep burial. The preservation of macropores during PSC allows the preservation of permeability. In addition, calcite solubility is positively dependent on mechanical parameters (axial compaction and axial stress), thus suggesting that calcite can precipitate during decompression of deep basinal fluids, resulting in changes in porosity. A comparison of experimental results with theoretical calculations showed that the integration of the PSC process into calculation databases would greatly improve the modeling of DBR.
31 May 2024 in International Journal of Coal Science & Technology
The enhanced coalbed methane recovery using CO2 injection (CO2-ECBM) is widely proposed as a way of achieving the energy transition and reducing atmospheric CO2 in areas such as the Lorrain basin in France, where heavy industry is responsible for huge CO2 emissions and coal mines have been closed for more than a decade. This paper deals with the feasibility of extracting methane from the Lorraine basin using CO2-ECBM by comparing data from sorption isotherms, thermogravimetric analyses and breakthrough curves for two coal samples. One is bituminous (Box 18), from Folschviller (France) and is compared with another sub-bituminous (TH01) from La Houve (France), which is used as a reference because it was identified as a good candidate for CO2-ECBM in a previous research program. The quantities of adsorbed gases (CO2/CH4) obtained by sorption isotherms, thermogravimetry and CO2 breakthrough curves showed that Box 18 adsorbs more CO2 and CH4 than TH01 due to its higher porosity and good affinity for gases (CO2/CH4). Tόth model fits the experimental CH4 and CO2 adsorption isotherms better, reflecting the fact that the adsorption surface of the coals studied is heterogeneous. Adsorption enthalpies obtained by calorimetry indicated physisorption for gas-coal interactions, with higher values for CO2 than for CH4. Thermogravimetric analyses and breakthrough curves carried out at up to 50% relative humidity showed that the adsorption capacity of CO2 decreases with increasing temperature and the presence of water, respectively. The compilation of these experimental data explained the adsorption process of the studied coals and revealed their advantages for CO2-ECBM.