Hidekazu Kobatake

Hidekazu Kobatake

Auto-generated profile, based on publicly available information

Hidekazu Kobatake

Department of Science of Environmental and Mathematical Modeling, Graduate School of Science and Engineering, Doshisha University, Kyotanabe, Japan

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

31 May 2011 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
MAMasayoshi Adachi
Masayoshi Adachi
KMKazuo Maeda
Kazuo Maeda
ATAkikazu Tanaka
Akikazu Tanaka
HKHidekazu Kobatake
Hidekazu Kobatake
HFHiroyuki Fukuyama
Hiroyuki Fukuyama

1 January 2008 in Journal of Mineralogical and Petrological Sciences
Verified
Journal Article
Open access
KNKen Nagashima
Ken Nagashima
YMYoshinobu Moriuchi
Yoshinobu Moriuchi
KTKatsuo Tsukamoto
Katsuo Tsukamoto
KTKyoko K. Tanaka
Kyoko K. Tanaka
HKHidekazu Kobatake
Hidekazu Kobatake

30 December 2024 in ISIJ International
Verified
Journal Article
Open access
PDF file
YSYusaku Seimiya
Yusaku Seimiya
HKHidekazu Kobatake
Hidekazu Kobatake
KTKazuki Tono-Oka
Kazuki Tono-Oka
RSRiku Sugahara
Riku Sugahara
SKShuya Kurosawa
Shuya Kurosawa
SOShumpei Ozawa
Shumpei Ozawa
The thermophysical properties of molten Fe–Cu alloys, including density, surface tension, and viscosity, were measured using the electrostatic levitation furnace aboard the International Space Station (ISS-ELF) under microgravity conditions, which provided an environment that facilitated accurate measurements. The densities of the molten Fe–25at%Cu and Fe–50at%Cu alloys decreased linearly with increasing temperature, and higher copper compositions resulted in increased density. The surface tension of the molten alloys exhibited a unique up-convex temperature dependence curve that initially increased and then decreased as the temperature increased. Viscosity measurements indicated that the viscosity of the molten Fe–Cu alloys decreased with increasing temperature, following a quadratic curve, and that an increase in the copper composition resulted in lower viscosity.

1 January 2023 in High Temperature Materials and Processes
Verified
Journal Article
Open access
PDF file
YSYusaku Seimiya
Yusaku Seimiya
STShuto Tomita
Shuto Tomita
TKTohei Kawaguchi
Tohei Kawaguchi
HKHidekazu Kobatake
Hidekazu Kobatake
JBJürgen Brillo
Jürgen Brillo
SOShumpei Ozawa
Shumpei Ozawa
Round-robin measurement of surface tension of high-temperature liquid platinum was conducted free of any contamination from the supporting materials and oxygen adsorption, using an electrostatic levitator (ESL), two electromagnetic levitator (EML), and an aerodynamic levitator (ADL). The measured temperature dependences of the surface tension using ESL and two EMLs were in good agreement and were expressed as σ = 1,798 ± 74.3 − ( 0.12 ± 0.0445 ) × ( T − 2,041 ) \sigma =\mathrm{1,798}\pm 74.3-(0.12\pm 0.0445)\times (T-\mathrm{2,041}) [10 –3 N·m –1 ] (1,900–2,600 K). However, the surface tension values measured with ADL were slightly lower than those exceeding the uncertainty of the measurement plots at high temperatures.

15 May 2024 in ISIJ International
Verified
Journal Article
Open access
PDF file
KKKanta Kawamoto
Kanta Kawamoto
TGTakuya Goto
Takuya Goto
HKHidekazu Kobatake
Hidekazu Kobatake
The heats of fusion of Fe, Ni, and Co were measured using a closed-type aerodynamic levitation method to prevent chemical interactions with the container and oxidation of the samples. The hypercooling limits of these metals were experimentally determined using the correlation between the undercooling temperature and thermal plateau time. The heats of fusion of the metals were obtained as the product of the hypercooling limit and the isobaric heat capacity. The experimentally determined hypercooling limits for Fe, Ni, and Co were 280, 414, and 360 K, respectively. Using these hypercooling limits, the heats of fusion of pure Fe, Ni, and Co were determined as 12.7 ± 2.2 kJ mol-1, 16.9 ± 5.6 kJ mol-1, 14.8 ± 2.8 kJ mol-1, respectively. Notably, these experimentally determined heats of fusion using the closed-type aerodynamic levitation method closely align with the literature values within the range of experimental uncertainty, affirming the reliability of this measurement technique.