Ridvan Gecu

Ridvan Gecu

Auto-generated profile, based on publicly available information

Ridvan Gecu

Department of Metallurgical and Materials Engineering, Yildiz Technical University, Istanbul, Turkey

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications


2 August 2023 in Ceramics International
Verified
Journal Article
Closed access
FEFatma Sezgi Eraslan
Fatma Sezgi Eraslan
ITIrem Cemre Turu
Irem Cemre Turu
MOMucahid Ozcan
Mucahid Ozcan
BBBurak Birol
Burak Birol
RGRidvan Gecu
Ridvan Gecu

12 September 2022 in Transactions of the IMF
Verified
Journal Article
Closed access
RGRidvan Gecu
Ridvan Gecu
BBBurak Birol
Burak Birol
MÖMücahid Özcan
Mücahid Özcan
Al2O3, TiO2, and Al2O3-TiO2 coatings were deposited on AISI 304 stainless steel plates by the sol–gel dipping technique, and the effects of the coating composition on microstructure, wear, and corrosion characteristics were examined. Tribological features were determined by ball-on-disc sliding tests against an Al2O3 ball under a 10 N load, while corrosion properties were evaluated by potentiodynamic polarisation tests performed in 3.5% wt. NaCl solution. γ-Al2O3, α-Al2O3, and rutile phases were detected in the hybrid coatings. The highest coating thickness was obtained in single Al2O3 film and decreased with an increasing amount of TiO2 nanoparticles. The single Al2O3 layer had both the highest wear resistance and the lowest corrosion resistance. Although TiO2 addition caused an increase in the wear rate, it improved the corrosion resistance of the coating by filling the voids in the Al2O3 film. The Al2O3-TiO2 hybrid film with a relative ratio of 6:1 as a candidate for the wear- and corrosion-resistant coating decreased wear and corrosion losses of the 304 substrates by 83% and 97%, respectively.

1 August 2024 in Materials Research Express
Verified
Journal Article
Open access
AYAhmet Fatih Yayla
Ahmet Fatih Yayla
RGRidvan Gecu
Ridvan Gecu
NSNuri Solak
Nuri Solak
KKKursat M. Kazmanli
Kursat M. Kazmanli
MUMustafa Urgen
Mustafa Urgen
This study investigated residual stress evaluations during gaseous nitriding of 50CrMo4 and 31CrMoV9 steels. The nitriding processes were carried out in the NH3/H2/N2 atmosphere at 525 °C for 2 h by controlling the nitriding potential. The development of depth-dependent residual stresses was conducted using a Vickers indentation instrument with an estimated geometric correction. The obtained results correlated with the sublayer removal-assisted XRD sin2ψ method. Diffusion layers between 135 and 200 μm were obtained for all samples upon nitriding. The surface hardness values reached 475 HV for 50CrMo4 and 825 HV for 31CrMoV9 steels. The geometric correction factor α was calculated as 78° for a Vickers indenter to measure residual stresses. The generated compressive residual stresses by nitriding increased with increasing nitriding potential by 71% (from −350 to −600 MPa) and 13% (from −750 to −850 MPa) for 50CrMo4 and 31CrMoV9 steels, respectively. An approximately linear relationship was obtained between the hardness and residual stress profiles of the nitrided samples.