Fareed Elgabbas

Fareed Elgabbas

Auto-generated profile, based on publicly available information

Fareed Elgabbas

Ph.D. Candidate, Dept. of Civil Engineering, Univ. of Sherbrooke, Sherbrooke, QC, Canada J1K 2R1

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2015 in Journal of Composites for Construction
Verified
Journal Article
Closed access
BBBrahim Benmokrane
Brahim Benmokrane
FEFareed Elgabbas
Fareed Elgabbas
EAEhab A. Ahmed
Ehab A. Ahmed
PCPatrice Cousin
Patrice Cousin

1 October 2015 in Construction and Building Materials
Verified
Journal Article
Closed access
FEFareed Elgabbas
Fareed Elgabbas
EAEhab A. Ahmed
Ehab A. Ahmed
BBBrahim Benmokrane
Brahim Benmokrane

1 April 2016 in Composites Part B: Engineering
Verified
Journal Article
Closed access
FEFareed Elgabbas
Fareed Elgabbas
PVPatrick Vincent
Patrick Vincent
EAEhab A. Ahmed
Ehab A. Ahmed
BBBrahim Benmokrane
Brahim Benmokrane

1 June 2017 in Journal of Composites for Construction
Verified
Journal Article
Closed access
FEFareed Elgabbas
Fareed Elgabbas
Ehab A. AhmedEhab A. Ahmed
Ehab A. Ahmed
BBBrahim M. Benmokrane
Brahim M. Benmokrane
Recently, basalt fiber–reinforced polymer (BFRP) reinforcement emerged as a new FRP type. Research is needed, however, to understand the behavior of BFRP bars in concrete members. This paper presents an experimental study aimed at investigating the flexural behavior and serviceability performance of concrete beams reinforced with ribbed BFRP bars. A total of eight concrete beams measuring 3,100 mm in length×200 mm in width×300 mm in depth were constructed and tested up to failure. Six beams were reinforced with 8-, 12-, and 16-mm BFRP bars with ribbed surfaces and two reference beams were reinforced with 10M and 15M steel bars. The beam specimens were designed in accordance with Canadian standards, and tested under four-point bending over a clear span of 2,700 mm until failure. The test results are presented and discussed in terms of cracking behavior, deflection, and failure modes. The test results yielded an average bond-dependent coefficient (kb) of 0.83, which is lower than 1.0 recommended b...

1 May 2020 in Construction and Building Materials
Verified
Journal Article
Closed access
MKMohamed G. Khalil
Mohamed G. Khalil
FEFareed Elgabbas
Fareed Elgabbas
MSMohamed samy
Mohamed samy
HEHany El-Shafie
Hany El-Shafie

1 July 2016 in Journal of Bridge Engineering
Verified
Journal Article
Closed access
FEFareed Elgabbas
Fareed Elgabbas
Ehab A. AhmedEhab A. Ahmed
Ehab A. Ahmed
BBBrahim M. Benmokrane
Brahim M. Benmokrane
Advances in fiber-reinforced polymer (FRP) technology have led to the introduction of new basalt-fiber-reinforced-polymer (BFRP) bars. This paper presents a research project investigating the behavior of edge-restrained concrete bridge-deck slabs reinforced with BFRP bars. The tests included six full-scale edge-restrained concrete deck slabs simulating a slab-on-girder bridge deck commonly used in North America and one full-scale unrestrained concrete deck slab. The deck slabs measured 3,000 mm long × 2,500 mm wide × 200 mm thick. The test parameters investigated were (1) reinforcement type (BFRP and steel); (2) BFRP bar size (12 and 16 mm); (3) reinforcement ratio in each direction (0.4–1.2%); and (4) edge-restraining [restrained or unrestrained (free)].The slabs were tested up to failure over a center-to-center span of 2,000 mm under a single concentrated load acting on the center of each slab over a contact area of 600 × 250 mm to simulate the footprint of a sustained truck wheel load (87.5-kN ...