Bowen Deng

Bowen Deng

Auto-generated profile, based on publicly available information

Bowen Deng

College of Electronic Science and Technology, National University of Defense Technology, Changsha, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 January 2021 in IEEE Internet of Things Journal
Verified
Journal Article
Closed access
MLMingtuan Lin
Mingtuan Lin
MXMing Xu
Ming Xu
XWXiang Wan
Xiang Wan
HLHanbing Liu
Hanbing Liu
ZWZhaofeng Wu
Zhaofeng Wu
SZSong Zha
Song Zha
With the small sampling length, a novel Direction-of-Arrival (DOA) estimation method based on a single programmable metasurface sensor is proposed in this article. Serving as a physical random sampling receiver, a dynamic metasurface generates series of random radiation patterns to sense the incident signals, which is subsequently processed by the compressive sensing (CS) orthogonal matching pursuit (OMP) algorithm to recover the DOA information. A mathematical model of DOA estimation is first built for theoretical analyses. Furthermore, numerical simulations are investigated with extensive performance analyses. In comparison with the metasuface-based beam-scanning method, metasurface-based CS for DOA estimation has superior performance with a smaller sampling length. Finally, a proof-of-concept experiment is made to verify the feasibility of the programmable metasurface for DOA estimation. Compared to other traditional estimation techniques that require multiple channels, the programmable metasurface can achieve estimation with only a single channel and small sampling length.

18 September 2020 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
BDBowen Deng
Bowen Deng
MLMingtuan Lin
Mingtuan Lin
Jihong ZhangJihong Zhang
Jihong Zhang
ZWZhaofeng Wu
Zhaofeng Wu
CLChenxi Liu
Chenxi Liu
PLPeiguo Liu
Peiguo Liu
In this article, a PIN-diode-based high-intensity radiation fields (HIRF) protection method was proposed and the sensitivity to the field intensity of incident wave has been verified by a printed dipole antenna loaded with three pairs of PIN diodes at S-band. To illustrate this method, an equivalent linear circuit was raised to analyze the basic operation principle of the proposed antenna. With a low-power incident wave, the PIN diodes are in off-state and the gain of the proposed antenna remains unaffected; while it drops considerably as the PIN diodes are triggered by HIRF. Furthermore, extensive parametric studies of the structure were analyzed by full-wave simulation to investigate the key factors affecting the performance of HIRF protection and antenna characteristics. Finally, a prototype was fabricated and experiments were implemented to verify the feasibility, which shows a high isolation of 19 dB. To the best of our knowledge, the proposed antenna is the first one to achieve HIRF protection through integrated antenna technology, which features with low cost and compact structure, providing a new perspective.

27 April 2023 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
ZWZhaofeng Wu
Zhaofeng Wu
PLPeiguo Liu
Peiguo Liu
BDBowen Deng
Bowen Deng
TTTao Tian
Tao Tian
SZSong Zha
Song Zha
XNXiaocheng Ni
Xiaocheng Ni
In this article, a novel nonreciprocal energy selective surface (ESS) concept is proposed against high-intensity radiation field (HIRF) threat, which has unidirectional HIRF isolation performance in ultra-broadband. The nonreciprocal ESS consists of an electromagnetic (EM) detector, a controlling module, and a controllable surface. The EM detector is used to monitor the forward electric field. When HIRF irradiation comes from the front, the controllable surface is triggered by the detector from transparent to opaque, thus isolating the HIRF to protect the back-end sensitive equipment. On the contrary, the backward HIRF cannot trigger the controllable surface, thus ensuring that the HIRF can radiate out. To illustrate this concept, an ultrabroadband nonreciprocal ESS prototype is designed and fabricated. The results of the simulation and measurement prove that the designed ESS has low insertion loss for small signals and shows nonreciprocal high shielding effectiveness under HIRF. Furthermore, the ESS can work in an ultrabroadband covering 3.5–8.5 GHz. The proposed method can be used to protect HIRF-sensitive equipment that requires high-power EM radiation.

6 April 2021 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
Jihong ZhangJihong Zhang
Jihong Zhang
NHNing Hu
Ning Hu
ZWZhaofeng Wu
Zhaofeng Wu
BDBowen Deng
Bowen Deng
MLMingtuan Lin
Mingtuan Lin
PLPeiguo Liu
Peiguo Liu
This article presents an adaptive high-impedance surface (A-HIS) that can be applied in the prevention of high-intensity wave propagating in $X$ -band waveguide. Once the embedded diodes loaded on A-HIS are switched from OFF- to ON-states by the high-intensity incident wave, the boundary condition of the waveguide’s bottom wall would adaptively change from a perfect electric conductor (PEC) to a perfect magnetic conductor (PMC), and the propagation would be prevented. To demonstrate this nonlinear characteristic, eigenmodes of the periodic unit-cells in two states of diodes were calculated, and the dispersive performance was analyzed. The bandwidth was further derived through the bandgaps between its intrinsic modes. Finally, a prototype with $5\times 10$ elements was designed, fabricated, and measured in a WR90 waveguide. The results indicate that, on condition of incident wave with relatively low power intensity, signals can propagate through the A-HIS with a low insertion loss by no more than 1 dB; in the case of relatively high power intensity, this loaded A-HIS can attenuate the incident wave by more than 10 dB and absorb more than 80% power within its operation bandwidth.

10 April 2024 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
BDBowen Deng
Bowen Deng
HDHao Ding
Hao Ding
PLPeiguo Liu
Peiguo Liu
YXYanlin Xu
Yanlin Xu
ZWZhaofeng Wu
Zhaofeng Wu
SZSong Zha
Song Zha
This article presents a series of intensity high-pass devices (IHPDs) that are designed and investigated to prevent the propagation of high-power microwaves (HPMs) in RF front-end systems. The IHPDs function as a band-stop filter for low-intensity waves and a bandpass filter for high-intensity waves. By combining an IHPD, a circulator, and a matched load, an intensity-dependent nonreciprocal component (IDNC) is created. The IDNC exhibits unidirectional transmission characteristics with high power backward input, thus achieving HPM protection. This article investigates and verifies the mechanisms and designs of IHPDs through measurements to meet various performance requirements. First, circuit models for diodes, circuit units, and IHPDs are established successively. Next, a standardized design procedure is presented, which clearly outlines the steps from specifications to implementation. The optimal values of the circuit components are determined by comparing them with the results of circuit and full-wave simulations. The measured results, including the $S$ -parameters, bandwidths, and thresholds, closely match the designed results. This method provides a new perspective and is suitable for high-power in-band full-duplex (IBFD) applications.

20 June 2022 in IEEE Transactions on Vehicular Technology
Verified
Journal Article
Closed access
MXMing Xu
Ming Xu
JLJibin Liu
Jibin Liu
SPShaopeng Pan
Shaopeng Pan
BDBowen Deng
Bowen Deng
Jihong ZhangJihong Zhang
Jihong Zhang
MLMingtuan Lin
Mingtuan Lin
A 1-bit low-profile patch antenna array integrating beam scanning and adaptive high-intensity radiation fields (HIRF) protection is proposed in this paper. Each antenna element consists of two dielectric layers, two radiation patches, a ground plane, and a feeding network. By electronically controlling a pair of coding diodes in the same direction, the antenna element can achieve 180 $^\circ$ phase difference, producing two logical states, namely “0” and “1”. It has good beam scanning capability in the range of −60 $^\circ$ to 60 $^\circ$ . When the proposed antenna is exposed to HIRF, the protective diodes mounted over the grounded coplanar waveguide (GCPW) transmission line are triggered, dramatically reducing the overall gain of the antenna array. By optimizing design, the element possesses a bandwidth of 8.8 $\sim$ 9.3 GHz. The grating lobe of the antenna array is suppressed by 17.5 dB thanks to the adoption of the non-uniform feed. The simulation results indicate that the proposed antenna element and array have a high isolation degree of 22.4 dB and 23.2 dB when exposed to HIRF, respectively. Finally, a prototype of the antenna is fabricated, and the validity of the proposed design is experimentally verified. The experimental results are in good agreement with the simulation results, demonstrating the validity of the proposed design.