Macromolecules Innovation Institute, Virginia Polytechnic Institute and State University, ICTAS II, Suite 130, 1070 Life Science Circle, Blacksburg, Virginia 24061, United States
Auto-generated profile, based on publicly available information
Arit Das
Macromolecules Innovation Institute, Virginia Polytechnic Institute and State University, ICTAS II, Suite 130, 1070 Life Science Circle, Blacksburg, Virginia 24061, United States
Filament‐based material extrusion (MatEx) additive manufacturing has garnered great interest due to its simplicity, customizability, and cost‐effectiveness. However, MatEx of semicrystalline polymers is still largely relegated to prototyping applications. Major issues involving volumetric shrinkage and warpage of the printed parts must be addressed in order to employ them for printing functional parts. Moreover, the crystallization behavior and rheology of the polymer are dependent on the MatEx processing conditions. In the current work, the printability of blends of isotactic polypropylene with a soft, low crystallinity propylene based homopolymer is evaluated. Addition of the homopolymer resulted in an increase in the crystallization window of the blends by ~6°C that had a profound impact on the interlayer adhesion and residual stress state. The shear‐dependent melt flow behavior inside the printing nozzle as well as the interlayer chain diffusion and interlayer welding on the print bed were investigated. Rheological characterizations also indicate sufficient dispersion and miscibility of the homopolymer in the neat polypropylene matrix. The incorporation of the homopolymer as an additive significantly improved the dimensional accuracy of the printed parts through better dissipation of the entrapped residual stresses during MatEx. Moreover, the degree of mechanical anisotropy of the parts was significantly lower than that obtained using many 3D printable grade polymers. The findings from this study can be leveraged in toolpath planning, process parameter optimization, and new feedstock development, highlighting current limitations as well as providing valuable insights into necessary processing modifications in order to enable MatEx of next generation semicrystalline polymers.
Semicrystalline polymers are an attractive feedstock choice for material extrusion (MatEx)-based three-dimensional printing processes. However, the printed parts often exhibit poor mechanical properties due to weak interlayer strength thereby limiting the widespread adoption of MatEx. Improved interlayer strength in the printed parts can be achieved through a combination of process parameter selection and material modification but a physics-based understanding of the underlying mechanism is not well understood. Furthermore, the localized thermal history experienced by the prints can significantly influence the strength of the interlayer welds. In this work, a combined experimental and modeling approach has been employed to highlight the relative impact of rheology, non-isothermal crystallization kinetics, and print geometry on the interlayer strength of printed parts of two semicrystalline polymers, namely, polylactic acid (PLA) and polypropylene (PP). Specifically, the print properties have been characterized as a function of print temperature and print speed. In the case of single road width wall (SRWW) PLA prints, the total crystalline fraction increases due to the broadening of the crystallization window at higher print temperatures and lower print speeds. The results are substantiated by the constitutive modeling results that account for the effects of quiescent crystallization. However, SRWW PP prints display a reduction in the interlayer properties with temperature likely due to significant flow-induced crystallization effects, as suggested by the model. Interestingly, in the case of multilayer PP prints, the repeated heating/cooling cycles encountered during printing counteracts the flow-induced effects leading to an increase in mechanical properties with print temperature consistent with SRWW PLA prints.
The fields of contaminant destruction and polymer nanocomposites are converging to immobilize photocatalysts for the degradation of conventional and emerging contaminants. Novel work exploits the design freedom of high-surface-area structures enabled by Additive Manufacturing to produce customizable, high-surface-area infilled structures containing photocatalysts. While investigations of nanoparticle dispersion in polymers for mechanical performance are available, there remains a specific need for environmental application-focused research to understand how processing impacts nanocomposite structure-property relationships for 3D printing in water treatment applications. This study investigated twin screw extrusion process parameters (temperature, screw speed, and number of extrusions) on the dispersion of photocatalytic TiO2 particles in a 3D printable polylactic acid (PLA) composite, the resulting effects on thermal processing properties, and ultimately whether there were benefits to photocatalytic performance. A Design of Experiments evaluated the aforementioned compounding parameters on the number, size, and location of TiO2 agglomerates in PLA (≈20% w/w TiO2). Significant correlations between different TiO2 dispersion states and thermal processing parameters were revealed. Higher TiO2 loadings (≈30 w/w) resulted in higher viscosity and modulus and a smaller processing window for reliable 3D printing. However, all printed structures tested demonstrated similar photocatalytic rates (≈0.32 to 0.37 ± 0.02 h-1). This is attributable to the observation of better dispersed TiO2 at the surfaces of printer extrudates and the actual printed structures, despite the differences in the initial agglomerate state related to larger agglomerates within the interior of the filament. These results suggest that TiO2 dispersion and distribution by twin screw extrusion are sufficient to achieve environmentally effective degradation rates if agglomerates are less than approximately 20 μm (an image analysis cutoff) and if these smaller agglomerates remain near the surface of printed structures. When such dispersion states are achieved, additional efforts to break up agglomerates appear nonessential for acceptable photocatalytic performance.