5 December 2023 in Energy & Environmental Science
Monolithic perovskite-based triple junction solar cells have the potential to surpass the power conversion efficiency (PCE) limits of single and dual-junction solar cells.
15 September 2023 in ACS Energy Letters
The efficiency of perovskite/silicon tandem solar cells has exceeded the previous record for III-V-based dual-junction solar cells. This shows the high potential of perovskite solar cells in multi-junction applications. Perovskite/perovskite/silicon triple-junction solar cells are now the next step to achieve efficient and low-cost multi-junction solar cells with an efficiency potential even higher than that for dual-junction solar cells. Here we present a perovskite/perovskite/silicon triple-junction solar cell with an open circuit voltage of >2.8 V, which is the record value reported for this structure so far. This is achieved through employing a gas quenching method for deposition of the top perovskite layer as well as optimization of interlayers between perovskite subcells. Moreover, for the measurement of our triple-junction solar cells, precise measurement procedures are implemented to ensure the reliability and accuracy of the reported values.
2 February 2023 in Solar RRL
Perovskite silicon tandem solar cells can overcome the efficiency limit of silicon single‐junction solar cells. In two‐terminal perovskite silicon tandem solar cells, current matching of subcells is an important requirement. Herein, a current‐matched tandem solar cell using a planar front/ rear side‐textured silicon heterojunction bottom solar cell with a p–i–n perovskite top solar cell that yields a high certified short‐circuit current density of 19.6 mA cm−2 is reported. Measures taken to improve the device are guided by optical simulation and a derived optical roadmap toward maximized tandem current density. To realize current matching of the two subcells, variation of the perovskite bandgap from ≈1.68 to 1.64 eV and thickness is investigated. Spectrometric characterization, in which current–voltage curves of tandem devices are recorded at systematically varied spectral irradiance conditions, is applied to determine the current matching point. In addition, remaining device limitations such as nonradiative recombination at the perovskite's interfaces are analyzed. Replacing the hole transport layer PTAA by 2PACz results in an overall certified power conversion efficiency of up to 26.8%. Precise simulation based on the device structure is essential as it provides efficient paths toward improving the device efficiency.
9 August 2023 in Advanced Materials Interfaces
The properly chosen light management strategy in perovskite solar cell devices is indispensable in achieving high power conversion efficiency. To diminish the reflection losses, texturization of the front surface, similar to what is used in established solar cell technologies, shall be taken into consideration. Within this paper, a honeycomb‐like textured SU‐8 photoresist layer is applied using a roller nanoimprint technique onto a planar perovskite solar cell to minimize reflection losses. The results show that the applied honeycomb pattern reduces the solar‐weighted reflectance from 13.6% to 2.7%, which enhances the current density of the unmodified cell by 2.1 mA cm−2, outperforming the commonly used planar MgF2 antireflective coating by 0.5 mA cm−2. The experimental results are combined with optical modeling to find optimized structures and predict the optical behavior within a solar module. The process used within this work can be transferred to perovskite‐silicon tandem solar cells, providing a promising pathway for the reflection reduction in future devices.
25 July 2024 in Solar RRL
Perovskite‐based triple‐junction solar cells have recently gained significant attention and are rapidly developing, thanks to the insights gained from the advancement in its dual‐junction counterparts. However, employing perovskite materials in multijunction solar cells with more than two junctions brings new challenges that have not yet been addressed. One aspect is the possibility of reverse bias breakdown of perovskite subcells during operation of the triple–junction device. This is more relevant for triple‐junction solar cells because a higher reverse voltage might drop at perovskite subcells compared to the case of dual‐junction solar cells. Herein, the breakdown voltages of the two perovskite subcells in perovskite/perovskite/silicon triple‐junction solar cells are determined by progressively increasing the reverse bias applied to the subcells in a single‐junction architecture during current–voltage measurements and monitoring the appearance of shunts using illuminated lock‐in thermography measurements. Furthermore, to analyze the effect on the final triple–junction solar cell, the triple‐junction device is brought in different current limitation conditions. It is shown that the subcell breakdown can happen during the operation of the triple‐junction solar cell, especially for the case where the perovskite top cell is limiting the overall current of the device. This effect is less severe when the middle perovskite cell limits the current due to the absence of a direct contact with the silver metallization which has shown to be the major degradation site during reverse biasing of perovskite solar cells. Finally, there is no concern regarding breakdown of the silicon bottom cell due to the higher breakdown voltage of silicon compared to perovskite.