1 September 2021 in Composites Part B: Engineering
1 January 2018 in AIP Conference Proceedings
Automated fiber placement (AFP) provides precision and repeatable manufacturing of both simple and complex geometry composite parts. However, AFP also introduces the possibility for unique flaws such as overlapping tows, gaps between tows, tow twists, lack of layer adhesion and foreign object debris. These types of flaws can all result in a significant loss of performance in the final part. The current inspection method for these flaws is a costly and time intensive visual inspection of each ply layer. This work describes some initial efforts to incorporate thermal inspection on the AFP head and analysis of the data to identify the previously mentioned flaws. Previous bench-top laboratory experiments demonstrated that laps, gaps, and twists were identified from a thermal image. The AFP head uses an on- board lamp to preheat the surface of the part during layup to increase ply consolidation. The preheated surface is used as a thermal source to observe the state of the new material after compaction. We will present data collected with the Integrated Structural Assembly of Advanced Composites (ISAAC) AFP machine at Langley Research Center showing that changes to the temperature profile is sufficient for identifying all types of flaws.
8 May 2019 in AIP Conference Proceedings
The advent of Automated Fiber Placement (AFP) systems have aided the rapid manufacturing of composite aerospace structures. One of the challenges that AFP systems bring is the variability of the deposited prepreg tape layers, which are prone to gaps, overlaps and twists. The current detection method used in industry involves halting fabrication and performing a time consuming visual inspection of each tape layer. Typical AFP systems use a quartz lamp to heat the base layer to make the surface tacky as it deposits another tape layer. The innovation discussed in this paper is to use the preheated base layer as a through transmission heat source and inspect the newly added tape layer in situ using a thermographic camera mounted onto the AFP structure. Such a system would not only increase manufacturing throughput by reducing inspection times, but would also aid in process development for new structural designs or material systems. To this end, a small thermal camera was mounted onto an AFP robotic research platform at NASA, and thermal data was collected during typical and experimental layup operations. The data was post processed to reveal defects such as tow overlap/gap, wrinkling, and peel-up. Defects that would have been impossible to detect visually were also revealed in the data, such as poor/loss of adhesion between plies and the effects of vacuum debulking. This paper will cover the results of our experiments, and the recent progress on the data reduction algorithms in preparation for machine learning development.
1 January 2017 in AIP Conference Proceedings
Reducing the timeline for certification of composite materials and enabling the expanded use of advanced composite materials for aerospace applications are two primary goals of NASA’s Advanced Composites Project (ACP). A key a technical challenge area for accomplishing these goals is the development of rapid composite inspection methods with improved defect characterization capabilities. Ongoing work at NASA Langley is focused on expanding ultrasonic simulation capabilities for composite materials. Simulation tools can be used to guide the development of optimal inspection methods. Custom code based on elastodynamic finite integration technique is currently being developed and implemented to study ultrasonic wave interaction with manufacturing defects, such as in-plane fiber waviness (marcelling). This paper describes details of validation comparisons performed to enable simulation of guided wave propagation in composites containing fiber waviness. Simulation results for guided wave interaction with in-plane fiber waviness are also discussed. The results show that the wavefield is affected by the presence of waviness on both the surface containing fiber waviness, as well as the opposite surface to the location of waviness.
16 August 2018 in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
This paper presents data from an innovative nondestructive evaluation method for automated composite fiber placement fabrication. Using Infrared images of the fiber as it was being placed we are able to provide valuable information about the quality of the part during fabrication. Herein, we discuss the methodology for data collection and processing. The described in-situ thermal nondestructive evaluation process is found to be applicable for identifying fiber tow overlaps, gaps, twists, puckering and poor ply adhesion prior to cure, thereby reducing the time and cost associated with post cure flaw repair or scrapping parts. This paper also describes the process of assembling data sets for an entire part beyond simple frame by frame analysis. Example data sets for both a flat part and a larger cylindrical part are presented to demonstrate the type of defect characterization information that can be obtained.