Manabu Tokushige

Manabu Tokushige

Auto-generated profile, based on publicly available information

Manabu Tokushige

Graduate School of Engineering, Chiba University

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2014 in ECS Transactions
Verified
Journal Article
Open access
BKBabak Khalaghi
Babak Khalaghi
EKEirin Kvalheim
Eirin Kvalheim
MTManabu Tokushige
Manabu Tokushige
LTLidong Teng
Lidong Teng
SSSeshadri Seetharaman
Seshadri Seetharaman
GHGeir Martin Haarberg
Geir Martin Haarberg
An electrochemical study of iron was carried out in KCl+LiCl+NaCl melt at 550ºC using a glassy carbon working electrode. Cyclic voltammetry showed that the Fe(II)/Fe(0) electron exchange is a soluble/insoluble reversible process. The diffusion coefficient of Fe(II) was calculated using cyclic voltammetry; 1.4×10-5 cm2 s-1. For the Fe(II)/Fe(III) red/ox reaction, analysis of the voltammograms suggests that the process is not reversible and is coupled with a chemical reaction. The stability of FeCl3 and the effect of equilibrium between FeCl3 and FeCl2 are also briefly discussed.

1 November 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
MTManabu Tokushige
Manabu Tokushige
OKOle Edvard Kongstein
Ole Edvard Kongstein
GHGeir Martin Haarberg
Geir Martin Haarberg
Iron alloys were produced by suspension electrolysis in a 50 wt % NaOH–H 2 O electrolyte at 383 K, and Fe–Cr and Fe–Ni alloys were obtained using a suspension of Fe 2 O 3 +Cr 2 O 3 and Fe 2 O 3 +Ni(OH) 2 particles, respectively. Highly ordered columnar deposits comprising cubic Fe–Cr particles with approximately 5-micrometer-long sides were obtained on a disk cathode with a current efficiency higher than 90% at 100–300 mA・cm −2 . In contrast, disordered columnar deposits of Fe–Ni particles with diameters of approximately 1.0 μ m were obtained on a disk cathode with a current efficiency of approximately 50% at 200 mA・cm −2 . The proposed method affords iron alloys with compositions in the stainless-steel region that depend on the electrolysis conditions, namely, the current density and Fe 2 O 3 /Cr 2 O 3 or Fe 2 O 3 /Ni(OH) 2 content ratio.

1 June 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
MTManabu Tokushige
Manabu Tokushige
This study characterizes the oxide-ion diffusivities of fluorite and perovskite oxides for an inert anode in molten salts below intermediate temperatures (∼800 K) and investigates the morphologies of nanoparticles used for nanostructure-fabricating the inert anode to optimize the oxide-ion diffusivity using phonon vibration. The isotropic phonon vibration of each material was estimated using high-temperature X-ray diffraction measurements. Both fluorites and perovskites exhibited a tendency for high oxide-ion diffusivity, as confirmed at a high-vibrational, oxide-ion frequency. Crystal anisotropy measurements of phonon vibration indicated that the oxide ions diffuse isotropically and three-dimensionally in each crystallographic face of fluorites while they diffuse preferentially along the ( a , b ) plane in perovskites. These results suggest that the oxide-ion diffusivity was improved using spherical fluorite nanoparticles and curtailed using layered perovskite particles.

15 December 2025 in ISIJ International
Verified
Journal Article
Open access
PDF file
RFRyota Fujisawa
Ryota Fujisawa
MTManabu Tokushige
Manabu Tokushige
JRJunichi Ryu
Junichi Ryu
A new ammonia separation method for the Haber–Bosch process, which is absorption separation, requires ammonia absorbents that are applicable at high temperatures. This study investigated the ammonia absorption/desorption behaviors of CaCl2-based absorbents (CaCl2-LiCl, CaCl2-LiBr, and CaCl2-NaCl) at 473 K using pressure-swing absorption (0.1–0.5 MPa). CaCl2 containing small amounts of lithium compounds (LiCl or LiBr) exhibited higher ammonia absorption and desorption rates than the CaCl2 single salt. Particularly, the ammonia absorption and desorption rates of CC100LC1 (with a molar ratio of CaCl2 : LiCl = 100 : 1) were 23% and 11% higher than those of the CaCl2 single salt, respectively. The ammonia absorption capacity of CC100LC1 was higher than those of conventional ammonia absorbents such as Na-Y zeolite and comparable to that of the CaCl2 single salt. The CaCl2-LiCl mixture is a promising ammonia absorbent for absorption separation because it can easily absorb/desorb ammonia at high temperatures.

12 February 2026 in The Journal of Physical Chemistry C
Verified
Journal Article
Closed access
MTManabu Tokushige
Manabu Tokushige
GHGeir Martin Haarberg
Geir Martin Haarberg

20 February 2026 in Electrochimica Acta
Verified
Journal Article
Closed access
MTManabu Tokushige
Manabu Tokushige
TKTakao Kunihiro
Takao Kunihiro