Pranab Saha

Pranab Saha

Auto-generated profile, based on publicly available information

Pranab Saha

Kolano and Saha Engineers, Inc

Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2012 in Progress of Theoretical and Experimental Physics
Verified
Journal Article
Open access
PDF file
HHHideaki Hotchi
Hideaki Hotchi
HHHiroyuki Harada
Hiroyuki Harada
NHNaoki Hayashi
Naoki Hayashi
MKMichikazu Kinsho
Michikazu Kinsho
PSPranab Saha
Pranab Saha
MSMasashi Shirakata
Masashi Shirakata
The 3-GeV rapid cycling synchrotron (RCS) of the Japan Proton Accelerator Research Complex (J-PARC) is a high-power pulsed proton driver aiming at 1 MW output beam power. The RCS was beam commissioned in October 2007 and made available for user operation in December 2008 with an output beam power of 4 kW. Since then, the output beam power of the RCS has been steadily increasing following progressions in beam tuning and hardware improvements. So far, the RCS has successfully achieved high-intensity beam trials of up to 420 kW at a low-level intensity loss of less than 1%, and the output beam power for the routine user program has been increased to 210 kW. The most important issues in increasing the output beam power are the control and minimization of beam loss to maintain machine activation within the permissible level. This paper presents the current status of the RCS beam power ramp-up, with particular emphasis on our approach to beam loss issues. The future prospects of RCS beam commissioning and operation are also described.

8 April 2021 in Physical Review Accelerators and Beams
Verified
Journal Article
Open access
PDF file
IYIppei Yamada
Ippei Yamada
MWMotoi Wada
Motoi Wada
KMKatsuhiro Moriya
Katsuhiro Moriya
JKJunichiro Kamiya
Junichiro Kamiya
PSPranab Kumar Saha
Pranab Kumar Saha
MKMichikazu Kinsho
Michikazu Kinsho
A transverse beam profile monitor that visualizes a two-dimensional beam-induced fluorescent image was developed. The monitor employs a sheet-shaped gas flow formed by a technique of rarefied gas dynamics. A simplified analysis method was developed to reconstruct the beam intensity profile from the obtained image. The developed profile monitor and the analysis method were applied to measure the J-PARC 3 MeV H− beam profile. The root mean square values of the profiles were consistent with the ones obtained by a wire-scanning-type beam profile monitor. The beam loss due to the gas sheet injection was measured as a beam-current reduction. The amount of the beam current decreased in proportion to the gas sheet flux and the reduction ranged from 0.004 to 2.5%. The assembled system was capable of reconstructing a beam profile from a single shot beam pulse (1.7×1013 protons in 50  μs).

20 June 2025 in Physical Review Accelerators and Beams
Verified
Journal Article
Open access
PSP. K. Saha
P. K. Saha
HHH. Harada
H. Harada
FTF. Tamura
F. Tamura
KOK. Okabe
K. Okabe
MYM. Yoshimoto
M. Yoshimoto
HHH. Hotchi
H. Hotchi
At the 3-GeV rapid cycling synchrotron (RCS) of the Japan Proton Accelerator Research Complex, we have minimized the beam loss at high-intensity beam operation up to the designed beam power of 1 MW. This was accomplished through systematic numerical simulations and experimental studies conducted over 2 years from 2020 and 2022. We first focused on mitigating uncontrolled beam losses originating from the foil scattering of the circulating beam, which results in high residual radiation levels, particularly in the injection area. These uncontrolled beam losses were well mitigated by reducing the stripper foil size and optimizing the injection beam size. Subsequently, we attempted to minimize the space charge effects and the associated beam losses at 1 MW by implementing several measures, such as refining both longitudinal and transverse injection paintings, correcting betatron resonances, and optimizing betatron tunes at injection. Consequently, we reduced beam losses throughout the RCS, including the collimator area, by 80% as compared to those observed at 1-MW trial operation in 2020. The residual beam loss at 1 MW is now estimated to be well below 10 − 3 , which is primarily attributed to residual foil scattering-induced beam losses. Notably, beam losses in areas other than the collimator section are uncontrolled and required to be well minimized to ensure stable operation and regular accelerator maintenance. We have considerably reduced the machine activation, achieving a 1-order-of-magnitude decrease at the collimator compared to that in 2020. This improvement has enabled the RCS to maintain more than 98% availability for user operation recently. The simulation and measurement results, demonstrating good agreement, provide a detailed understanding of the beam loss mechanism at each step and guide the implementation of effective optimizations.

1 May 1993 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
RKRichard A. Kolano
Richard A. Kolano
WBWilliam S. Beggs
William S. Beggs
PSPranab Saha
Pranab Saha
The purpose of this paper is to identify various concerns that need to be evaluated prior to the design and construction of a reverberation chamber, such that the chamber can be used for various automotive related acoustical measurements. Some of the concerns involve issues such as room shape and size, the degree of sound and vibration isolation required, the use of conventional building materials versus traditional massive construction, construction cost, and the performance requirements for the test noise generation system. Various uses of a reverberation chamber include random incidence sound absorption measurements, small sample sound transmission loss measurements, vehicle insertion loss tests, dash panel, door, and other “buck” evaluation tests, and sound power level measurements of small automotive components and devices. These uses have differing and in some cases conflicting requirements that compete in the selection of room design parameters. The paper discusses these issues including the requirements for sound level generation in the chamber for proper measurements. The paper also provides case studies on the use of reverberation chambers for automotive applications.

31 May 2023 in Physical Review Accelerators and Beams
Verified
Journal Article
Open access
PDF file
YSYoshihiro Shobuda
Yoshihiro Shobuda
HHHiroyuki Harada
Hiroyuki Harada
PSPranab Kumar Saha
Pranab Kumar Saha
TTTomohiro Takayanagi
Tomohiro Takayanagi
FTFumihiko Tamura
Fumihiko Tamura
MYMasanobu Yamamoto
Masanobu Yamamoto
At the Rapid Cycling Synchrotron (RCS) in Japan Proton Accelerator Research Complex (J-PARC), theoretical predictions have indicated that the kicker impedance would excite the beam instability. A 1-MW beam with large emittance can be delivered to the Material and Life Science Experimental Facility through suppression of the beam instabilities by choosing the appropriate machine parameters. However, we require other high-intensity and high-quality smaller emittance beams (than the 1-MW beam) for the main ring. Hence, we proposed a scheme for suppressing the kicker impedance by using prototype diodes and resistors, thereby demonstrating the effect on the kicker impedance reduction. However, the J-PARC RCS must be operated with a repetition rate of 25 Hz, which urged us to consider special diodes that are tolerant to heating. After developments, we have demonstrated that the special diodes with resistors can suppress the beam instability by reducing the kicker impedance. Enhanced durability of the prototype diodes and resistors for the 25-Hz operation was also realized. Moreover, the new diodes and the resistors have a negligible effect on the extracted beam from the RCS. From a simulation point of view, the scheme can be employed for at least 5-MW beam operation within the stipulated specifications.

12 November 2001 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
PSPranab Saha
Pranab Saha
THThomas J. Henry
Thomas J. Henry
JCJohn Chahine
John Chahine
GDGregory T. Demrose
Gregory T. Demrose
This paper discusses an analytical tool that has been developed to predict what types of interior sound package treatments may be necessary in a truck cab to meet a predetermined target sound level at the driver location. The steps that were taken to develop this tool involved a combination of experimental measurement and analytical based studies. Measurements were conducted to identify the acoustic strengths of the major noise paths through which sound travels from outside to inside the truck. These findings were then used to develop a sound package that reduced the vehicle interior noise to meet the target. Measurements were primarily made on a chassis roll dynamometer with final road verification to substantiate the dynamometer data. Data obtained from these measurements were also used in the analytical model that predicts the impact of various acoustics parts in the vehicle, and has the capability to optimize the sound package treatment in the vehicle.