12 June 2024 in IEEE Transactions on Industry Applications
The increasing adoption of renewable energy sources (RES), such as solar photovoltaics and wind turbines, is transforming electricity generation. However, integrating RES within DC microgrids (DCM) for applications such as fast DC charging in electric vehicles (EVs) presents challenges, including low inertia, power fluctuations, and voltage instability. This study addresses these challenges with novel control strategies and optimization algorithms. A hybrid Firefly Algorithm-Particle Swarm Optimization (FA-PSO) approach is used to tune Takagi-Sugeno Fuzzy Inference Systems (TSFIS), Adaptive Neuro-Fuzzy Inference Systems (ANFIS), and Fractional Order Proportional-Integral-Derivative (FO-PID) controllers. This strategy optimizes power management within the DCM, ensuring faster convergence, superior accuracy, and reduced topological constraints. In addition, a comprehensive Small Signal Stability Analysis (SSSA) evaluates the impact of the proposed hybrid optimization techniques on DC microgrid stability. Crucially, a hardware prototype validates these strategies under real-world uncertainties, such as varying wind speed and solar insolation, demonstrating their effectiveness and feasibility for practical DC microgrid applications with integrated EV charging.
31 July 2024 in IEEE Transactions on Industry Applications
The integration of Renewable Energy Resources (RERs) into electrical grids introduces significant challenges concerning the reliability and stability of the grid. This paper focuses on these challenges, particularly the issues of real-time load forecasting and adaptive inertia control in renewable integrated grids. A data-driven, deep learning-based approach is proposed to dynamically forecast real-time load and renewable energy generation, using the New England IEEE 39-Bus Power System as a case study. To enhance the dynamic performance of the microgrid, the paper introduces an enhanced fractional extended state observer-based linear active disturbance rejection control mechanism coupled with a feedback architecture. This control scheme aims to provide adaptive inertia to the system, thus improving its ability to handle fluctuations and intermittencies inherent in RERs. The effectiveness of the proposed controller is rigorously compared with existing approaches through simulation studies, validating its superior performance for the IEEE 39-Bus Power System under examination. To further substantiate the findings, a hardware-in-loop real-time experimental analysis is conducted using OPAL-RT hardware. This hardware-based analysis serves as a functional validation of the proposed data-driven forecasting algorithm confirming its viability to improve the grid reliability.
22 January 2025 in IEEE Transactions on Consumer Electronics
Solar Photovoltaic (PV) power is the most common and efficient renewable energy source. The potential for utilizing solar PV energy on Earth is enormous. PV module characteristics significantly influence extracting maximum output from current solar power installations. Solar insolation and panel temperature substantially influence the voltage-current (V I) and power–voltage (P V) properties. The degree to which the system’s efficiency may be improved is determined by the accuracy with which the maximum power point tracking (MPPT) controller follows the nonlinear PV characteristics. This comprehensive investigation delves into the solar PV system dynamics, highlighting how modules induce power loss because of partial shading-induced peaks. Modified Adaptive Jaya Optimization (MAJO) is a novel meta-heuristic optimization approach designed to monitor maximum global power. MAJO boasts advantages over the conventional Deterministic Jaya Optimization (DM-Jaya) method under partial shading configurations (PSCs), exhibiting quicker convergence times and requiring fewer computing operations. MATLAB/Simulink and experimental scenarios are simulated and assessed under various environmental conditions, including step changes in solar irradiance, partial shading, and load variation, to evaluate the effectiveness of the proposed MAJO algorithm. The acquired findings are compared with the DM-Jaya and the Modified particle swarm optimization (MPSO), Maximum power trapezium (MPT) and Voltage window search (VSW) suggesting and demonstrating that the proposed MAJO algorithm yields better MPPT performance. Rigorous testing with a prototype experimental setup yielded a remarkable 99.9% tracking efficiency for the studied PSCs, accompanied by reduced settling times of 0.6s and convergence time of 0.154s. Additionally, the efficacy of the MAJO in terms of faster convergence characteristics, and attaining the optimal solution has been investigated on several unconstrained benchmark functions.
3 May 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The power transfer capacity of transmission lines is limited by the stability of the power system. Additionally, the dynamics of photovoltaic (PV) integration through the grid following inverter (GFI) affect the stability limits, which are not well studied in the literature. This paper, therefore, focuses on the stability-constrained power transfer capabilities of transmission lines with single-phase PV-GFI integration. An adaptive tuning method is proposed based on Lyapunov function analysis that increases the power transfer capability limit. Outer and inner control loop parameters are considered as candidates for the proposed method. The proposed tuning law is not affected by the active and reactive power requirements, low-voltage or over-voltage ride-through, network impedance, and load changes. Additionally, an active damping method utilizing a capacitor voltage feedback loop is proposed to eliminate the effect of resonance with improved power quality. The proposed method is validated through simulation and experimental verification for various test scenarios, such as sudden changes in solar irradiance, dynamic load changes, network parameter variation, and grid voltage sag-swell conditions. The proposed tuning method achieves an enhanced power transfer capacity limit compared with the existing method.
13 April 2023 in IEEE Transactions on Power Delivery
A PV three-phase grid following inverter (GFI) with LCL filters can reduce current harmonics and deliver active power to the grid. Controlling such higher-order systems is challenging due to system uncertainties, grid voltage variations, and filter resonance. Active disturbance rejection control (ADRC) provides resilience to these uncertainties and a prompt response to disturbances. A linear extended state observer and a phase-locked loop observer are integrated into the ADRC structure to optimize tracking performance. The proposed controller uses a structured inner and outer closed-loop ADRC that takes into account process delays and extended state observer dynamics. The GFI can operate under variable grid voltage frequencies or even deviations in frequency caused by grid failure, and is able to meet these challenges as part of the design process and the synchronization approach. Both simulation and experimental results are given to validate the dual ADRC-based methods for an 8 kW laboratory prototype PV-GFI system.
26 December 2022 in IEEE Transactions on Industry Applications
Only precise industrial applications can benefit from the high-frequency performance of variable-speed drives with low switching losses. A five-phase induction motor (FPIM) is connected to a voltage source inverter (VSI) via a $LC$ filter (low pass filter) to reduce high-frequency losses in the motor. A five-phase sinusoidal voltage is used to lower the high $dv/dt$ at the motor terminals. However, sustained resonant frequency oscillations destabilize closed-loop control of the FPIM drive at certain operational points. This paper presents and analyzes a variety of high-frequency SVPWM techniques, both continuous and discontinuous. It is also possible to optimize the switching frequency of the five-phase two-level VSI fed FPIM drive using an improved current ripple prediction method. Auxiliary circuits and high-frequency sensors are not necessary in this system, making it more stable. Simulated and experimental results are used to evaluate the stability of a drive under a variety of conditions.