Herein, we report a novel approach to obtaining magnesium and nanocrystal Mg-Al alloy from magnesia using a closed microwave aluminothermic method in order to solve the problems of high energy consumption, high pollution, and low productivity in the process of magnesium and its alloy production. The main idea of the paper is to design a technique for the preparation of magnesium–aluminum alloy during the reduction process of MgO directly under atmospheric pressure. Based on this experimental idea, we have established a closed microwave aluminothermic reduction reactor. The great advantage of the reaction device is that it can make the reaction material heat up quickly to the reaction temperature in the microwave heating process and produce high-pressure magnesium vapor, which reacts with aluminum dramatically to form Mg-Al alloy under microwave irradiation. By the calculation of the electromagnetic field of the reaction device and sample using ANSYS electronics desktop 2018, the optimum microwave heating conditions for samples have been established. Based on the calculation results, we demonstrate that magnesium and its alloy are prepared successfully by using this method. In addition, the reduction rate of MgO is greatly improved, which is higher up to 79.97 Wt% when the reduction time is 30 min, at 1273 K, and the Mg2Al3 and MgAl alloy is formed during the reduction process as well. Moreover, the formation mechanism of Mg-Al alloy during the reduction process under microwave irradiation was discussed further. Our findings could provide a new approach, insights, and research directions to obtain magnesium and Mg-Al alloy directly from magnesia under normal pressure.
Excellent resistance to steam oxidation is a key required property for heat-resistant alloys used in next-generation fossil power plants. In order to clarify the degradation mechanism of Ni-Fe-Cr alloys in high temperature steam, four kinds of Ni-Fe-Cr model alloys with various Cr content were prepared and their long-term steam oxidation were investigated at 650 °C and 700 °C. The microstructure and composition of oxide scales were characterized by SEM equipped with EDS, and the oxide phases were identified by XRD. The results showed significant dependence of temperature and Cr content in alloys on the oxidation kinetics, cross-section morphology and elemental section-distribution. For Ni-Fe-Cr alloys with low Cr contents (12∼16 wt.%), the increase of temperature made the oxide scale change from breakaway scale morphology (nodule-crater microstructure with external exfoliation) to protective scale morphology (uniform layer and internal oxidation). For Ni-Fe-Cr alloy with 18wt.% Cr, the effect of temperature was greatly reduced. The oxidation mechanism was discussed from the perspectives of selective oxidation and the effect of alloying elements.
Microbiologically influenced corrosion has become a predominant cause of pipeline and equipment failure in oil and gas fields. This research examines the corrosion behavior of steels with varying chromium contents in simulated shale gas formation water environments. Weight loss testing, Scanning Electron Microscopy (SEM), Energy Dispersive x-ray Spectroscopy (EDS), Focused Ion Beam (FIB), Transmission Electron Microscopy (TEM), and x-ray Photoelectron Spectroscopy (XPS) were employed. The findings suggest that an elevated Cr content in steel results in a gradual reduction in its uniform corrosion rate in a CO2-SRB coexistence environment. This can be primarily attributed to the significant distribution of Cr content throughout the entire product film, including both biofilm and corrosion products, thereby enhancing the product film’s protectiveness. Additionally, the competitive corrosion between CO2 and SRB, as well as the influence mechanism of Cr on corrosion, were discussed.
The electrodeposition of (Co,Mn)3O4 spinel precursor layers has emerged as a new method to prepare metallic interconnect coatings for solid oxide fuel cells (SOFCs). (Co,Mn)3O4 spinel films can be obtained via the oxidative heat treatment of an electrodeposited Co-Mn alloy layer. Herein, the effects of sandblasting stainless-steel substrates on the electrodeposition of the Co-Mn alloy were investigated. Sandblasting increased Co content in Co-Mn alloy, decreased the onset time of nucleation, and lead to surface nanocrystallization. Furthermore, sandblasting the substrate prevented the formation of the metal hydroxide interlayer, accelerated interdiffusion, and improved the adhesion of the (Co,Mn)3O4 spinel coatings.
The corrosion of hydraulic support has brought huge economic losses to coal enterprises. Using laser cladding stainless steel coating on the surface can improve its wear resistance and corrosion resistance. However, dense corrosion pits appeared on the hydraulic support coated 304 stainless steel after 25 d use in a coal mine. At present, there are few studies on the corrosion effect of this laser cladding layer under the actual mine. In this work, the oxide scales are characterized by 3D Optical Microscope (OM), Scanning Electron Microscopy (SEM) equipped with x-ray Energy Spectrometer (EDS), x-ray Photoelectron Spectrometer (XPS) and x-ray Diffraction (XRD) techniques. Based on the results, the localized corrosion mechanism is discussed. It was found that the corrosion products were mainly a mixture of (Fe,Cr)2O3 and CaCO3. The maximum pitting rate calculated from the depth data of pits. which were collected by ultra-depth of field optical microscopy, was 2.32 mm a−1. The mechanism of corrosion of hydraulic support was discussed form perspectives of the under-deposit corrosion and corrosive ions (i.e. Cl− and S2)− in the environment.