1 January 2019 in Mathematical Problems in Engineering
This paper takes a cross section of 6 × 7 + IWS wire rope as an example to complete the studies on a method of geometric modeling for no‐joint wire rope and implementation of a 3D solid model. Frenet–Serret frame theory establishes three types of Frenet–Serret frame, which are double‐helix winding straight line, single‐helix winding arc, and double‐helix winding arc, and it allows derivation of eight types of center line equation of wire. This paper has ascertained tangent condition of center lines of steel wires with the same name between arc and straight‐line wire rope and closed condition of no‐joint wire rope. It has been concluded that the length of steel wire must be an integer multiple of its lay pitch either in arc wire rope or in straight‐line wire rope, and the name of wires in each wire rope must be consistent at the same time. Finally, using Pro/ENGINEER Wildfire 5.0 software generates a 3D solid model of no‐joint wire rope.
25 November 2024 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
This study proposes a variable weight model prediction control strategy based on road surface recognition (VW-MPC-RSR), aiming to address the problems of road recognition timeliness and model prediction control (MPC) weight adjustment under multi-working conditions. The road surface recognition is achieved by utilizing the VIT-B/16 network model. A test set and a continuous frame video are used to verify the effectiveness of the road recognition strategy. At the same time, a 2-DOF suspension dynamics model is established, and the variable weight MPC control strategy based on road surface recognition is designed. The optimal weights of six road types are determined using a cross-comparison method, and the corresponding weight-switching strategy is formulated. The performance of VW-MPC-RSR active suspension, MPC active suspension, and passive suspension is compared by simulation. The results show that the road surface recognition strategy based on the VIT network can recognize various road states efficiently and accurately. In addition, the suspension control strategy designed in this paper can adjust the control parameters in real time according to road conditions and significantly improve the overall performance of suspensions.
25 June 2023 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
This study proposes a multi-mode switching control strategy based on electromagnetic hybrid suspension (EMHS) to achieve the best relationship possible between the vehicle’s vibration reduction performance and energy consumption. The working modes of EMHS are divided into active, semi-active, and energy recovery modes according to the relationship between the root mean square of weighted acceleration and the human subjective sensation. The two key switching parameters of the analysis sampling interval and switching judgment times are introduced to optimize the switching conditions and reduce the deterioration of comfort and handling stability caused by frequent system switching in mode switching decisions. In the sub-modes, it’s designed that an LQG main control loop uses an ant colony algorithm to optimize parameters to obtain the ideal output force. And inner-loop control strategies in active and semi-active modes are designed so that the actual force output by the actuator tracks the ideal force. The results show that the multi-mode switching control strategy can switch the EMHS reasonably in the three modes and achieve good vibration reduction performance. The RMS of SMA, SDD, and TDL are reduced by 27.5%, 6.3%, and 17.6%, respectively under the variable conditions road.
16 December 2023 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Traditional energy-feeding suspensions exhibit a non-adjustable damping characteristic during energy recovery, which can compromise the dynamic performance of the suspension system. To overcome this issue, this paper proposes an energy-feeding variable damping control strategy (EFVD) predicated on an electromagnetic hybrid suspension system. This strategy aims to achieve adjustable damping during energy recovery, reducing energy losses while ensuring optimal suspension performance. Building on a half-vehicle suspension model, we construct a dynamic model of the electromagnetic hybrid suspension. By leveraging an enhanced hybrid-skyhook and ground-hook control algorithm (HSGH), we solve for the target control force. We then design a force distribution controller based on the EFVD strategy, aiming to optimize suspension dynamic performance and energy feeding efficiency. And we conduct a simulation study, measuring power supply efficiency and suspension dynamic performance as key evaluation metrics. The results demonstrate the superiority of the proposed EFVD strategy over conventional passive and active suspension control strategies, highlighting its effectiveness and reliability in maintaining dynamic performance while enhancing energy efficiency. This underscores the potential of the EFVD strategy as a practical solution for future suspension system design and energy management.
4 July 2020 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
11 January 2022 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Steering Angle is related to the design and optimization of steering mechanism and suspension, but it is not equal to the angle of knuckle around kingpin because of the existence of wheel alignment parameters. To calculate the steering angle, this paper derives based on homogeneous transformation its function expression by analyzing spatial geometric relation between the two angles and calculating coordinates related to steering trajectory of wheel center. Then, multi-body model of McPherson suspension with steering system is built and the calculation correctness is verified by comparing the function curve plotted by MATLAB software with the curve simulated by Adams/Car software. The calculation and simulation indicate that between the two angles, there is a ratio which is related to wheel alignment parameters and greater than 1.